|
Tractor Talk Discussion Board |
Okay then, How Dumb is this idea?
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Allan on December 25, 2003 at 12:58:32 from (148.63.132.164):
Hi Guys, I spent all day yesterday preping and heating my garage floor; then I spent all Christmas morning putting down the first coat of this rubberized latex floor paint. While searching for a floor covering, I ran across a picture of a garage with a grey floor and knotty pine walls....One sharp looking garage!! So, I get to thinking this morning while I'm painting away the hours, "Why not just put up 1/2x6" tounge and groove straight siding for the walls and cover it with a varnish of some kind?". We used to do this all the time on the inside of wooden grain bins (without the varnish, of course). Does this make any sense? Is this stuff expensive? Would you share your thoughts? Thanks, Allan
Follow Ups:
- Re: Okay then, How Dumb is this idea? bob 17:06:03 12/26/03
(0)
- Re: Okay then, How Dumb is this idea? Mark in MO 13:02:07 12/26/03
(0)
- Re: Okay then, How Dumb is this idea? Mike M 09:29:12 12/26/03
(4)
- Re: Okay then, How Dumb is this idea? John S-B 08:39:54 12/26/03
(0)
- Re: Okay then, How Dumb is this idea? KURT 04:42:11 12/26/03
(1)
- Re: Okay then, How Dumb is this idea? Nebraska Cowman 04:32:41 12/26/03
(1)
- Re: Okay then, How Dumb is this idea? Charlie 23:34:19 12/25/03
(0)
- Re: Okay then, How Dumb is this idea? buck 19:47:32 12/25/03
(0)
- Re: Okay then, How Dumb is this idea? sod 19:39:44 12/25/03
(0)
- Re: Okay then, How Dumb is this idea? Bob 17:26:45 12/25/03
(2)
- Re: Okay then, How Dumb is this idea? Sonny Heath 17:08:38 12/25/03
(0)
- Re: Okay then, How Dumb is this idea? markct 16:45:39 12/25/03
(1)
- Re: Okay then, How Dumb is this idea? Binder-Man 16:34:37 12/25/03
(0)
- Re: Okay then, How Dumb is this idea? Kevin Bauza 16:30:06 12/25/03
(0)
- Re: Okay then, How Dumb is this idea? Phil 16:05:49 12/25/03
(0)
- Re: Okay then, How Dumb is this idea? oleblu 15:58:03 12/25/03
(0)
- Re: Okay then, How Dumb is this idea? Fawteen 13:50:23 12/25/03
(0)
Home
| Forums
Today's Featured Article -
My Ford Golden Jubilee - by Troy Estes. This article is about my '53 Ford Jubilee and a story that starts with taking the tractor to my brother's Starter/Alternator Rebuilding shop for a wiring fix. The generator was shot as well as all the wiring. I dropped off the tractor expecting a transformation from a 6 volt to a 12 volt system utilizing the original generator housing, and a total rewiring of the whole tractor. The front end center pin bushing was worn also so I ask that they replace it if they had time. Well, that’s wha
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
