Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: I beat the tractor


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by trucker40 on September 12, 2008 at 17:39:35 from (68.94.164.240):

In Reply to: I beat the tractor posted by Lanse on September 12, 2008 at 15:35:58:

Form A Gasket has its place.The trouble is its place is probably not in your tractor unless you know what you are doing.If you are talking about Silicon gasket sealer,its fine to smear a thin layer on a paper gasket to help seal it.You dont want to use any more than you need to,just a thin layer.Form A Gasket is a different kind of stuff supposedly to make a gasket out of and it might work,but its not necessary to replace a gasket like you are talking about with Form A Gasket when all you need is some gasket material to cut a new gasket out of,then coat lightly with silicon put together and if you have a lot of silicon that squeezes out,wipe it off so it wont get inside the motor.

On the hone it makes some difference which kind you have.If you have one with 3 stones you want to use penetrating oil,squirting on the hone stones while you run it up and down the cylinder kind of fast but not going out the bottom or top.More or less you do the same with the kind that has balls of abrasive on the end of nylon strings kind of like a brush,called a dingleberry hone,you squirt penetrating oil as you push it up and down the cylinder.With that kind of hone it doesnt take as long and it looks good if you do it right.Other things can be used besides penetrating oil,solvent,alcohol,maybe other stuff,but a can of WD 40 OR Liquid Wrench will do a V8 usually for me with a little left over.


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Tractor Parade: Story of a Case SC - by Bernie DeLon. On a early fall morning back in 1994, I opened the newspaper and happened to spy an article about a local antique tractor club having their annual show that weekend. ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy