Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: engine problem....help?!


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by txblu on December 07, 2004 at 09:58:58 from (199.46.199.231):

In Reply to: engine problem....help?! posted by cootbruce on December 07, 2004 at 08:28:32:

Only know what you tell us so here goes.

Moving the engine about could have dislodged some crud in the fuel system, say like crud at the bottom of the carb bowl got into some meterng jets. (You rebuilt the carb, but did you really rebuild it; i.e. clean out all the teenie weenie ports?).

Surging is inadequate governor control. You are over and under supplying your engine with the needed elements to run it. You could have damaged your governor linkage when removing especially on Tecumseh engines (my experience)...or if internal (like the Tec.) you may have gotten some sludge or other crud in the gov. bearings/balls. Remember the governor is rpm sensitive. What did you do that would affect the ability of your carburetor to be controlled as a function of rpm's.......speed up, gov shuts down air supply via carb throat butterfly......converse the converse.....sloppy linkage (incorrectly adjusted...length) means sloppy response of fuel/air to engine requirements.

Not showing a charge means that you broke a wire in handling, or pulled a lug off a terminal, or shorted out a terminal in your charging system. May have accidentally sparked the VR and welded some contacts.

Voltage and engine surge are 2 different ckts. Only connection could be via ignition supply voltage bouncing up and down and that's not possible as the battery has control (larger energy source) and voltage output not that much different at low and high rpm's as compared to engine off voltage value (0).

HTH

Mark


Follow Ups:




Post a Followup

:
: :

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - History of the Nuffield Tractor - by Anthony West. The Nuffield tractor story started in early 1945. The British government still reeling from the effects of the war on the economy, approached the Nuffield organization to see if they would design and build an "ALL NEW" British built wheeled tractor, suitable for both British and world farming. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy