Posted by SkiB on November 25, 2019 at 08:33:10 from (24.209.20.61):
Re-Roofing 30x40 Shed
I have a 30 depth x 40 width semi flat roof shed with a 2.5/12 pitch. The OEM roof has lasted some 50+/-years(?) and is slowly blowing off/spiting nails, rusting away. The building is salvageable.
Currently, I m repairing/replacing any structural wood and purlins boards in need of, as required. In addition, re-leveling the structure best I can. The leveling won t be perfect, but better than it current is.
Next year (spring 2020) project will be to re-side all walls and build new sliding doors with metal rib-metal sheathing over the weathered existing pine TG. At that time, I will be shortening the back wall to a 24 depth. This wind/weathered battered (western) wall is the worst condition of the entire building. Besides that, 4-1/2 of the building is "technically" on the Neighbor s land, which isn t a problem as legally all is good, plus having great neighbors helps. I just feel this is just another reason to to shorten up the back wall.
I m currently building a new header (pole construction wall vs the existing footer/block fountain) to support the lower end of all rafters (which will also assist in leveling).
MY QUESTION:
Before purchasing/installing my metal roof, what suggestions can be offered on the sheathing length?
2 thoughts at this time.....
Although theses are not my actual measurements, just to provide an example.
1) Would you purchase 30 length, then "shear" off what s not needed when new construction begins in 2020? Or.....
Would you purchase 24 pieces, then slip/tuck in a +6 piece to cover the remainder?
This building will always be a shed, so just trying to keeping costs at a minimum. Although the OEM had no vapor barrier underneath the metal and instead of me buying/installing all the fancy barrier stuff out there, would/could a simple layer of 30# roofing felt provide some protection?
Upload one or more videos to your post. Photo and video filesizes should be less than 8MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Fabricating Sidesheets - by Chris Pratt. The easiest and best first-time project for wanna-be sheet-metal workers like myself is flat or nearly flat metal cut and drilled to be a tractor's sidesheet. A sidesheet is sheetmetal to cover either the engine as in the case of early Oliver's, Massey-Harris' and many crawlers or the wiring and electrical components as in the case of the Massey-Harris Pony, Allis Chalmers' D Series (D-14, D-15, D-12, D-10, D-17, and D-19). The need for fabricating becomes obvious when you go to buy any of these
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
