Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Re: Farmall H generator


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bill Smith on November 21, 2001 at 21:57:19 from (128.242.4.59):

In Reply to: Re: Farmall H generator posted by Gene Davis on November 18, 2001 at 20:39:32:

A three pronged setup on the old regulator actually might be a cut out instead of a regulator. Take the old regulator cap off and see if there is one set of points or 2 or 3 sets of points. If just one set of points the regulator is actually a cut out. Another way to tell is if there is 4 settings on the light switch or just 3. If there is 4 the tractor was originally equiped with a cut out. Early H's had the cutout and later ones I believe had the regulator originally. The H was also positive ground from the factory. You can set it up both ways but make sure the generator is polarized the right way. If you switch to neg ground the amp meter should show a discharge when generator is charging. If you want to run it with negative ground you can switch wires around from one post to the other on the amp guage so it shows a charge instead of a discharge. You should also switch wires around on coil but the most important thing is polarizing generator the right way. The confusing part about this whole situation is not knowing what has been done by someone else over the years so just putting it back the way it was, might not necessarily be right. Take the time and investigate the charging system so that you know it is wired up right so it will work correctly. Regulators are exspensive and it doesn't take much to burn them up if not installed correctly. It just sounds to me like you are replacing a cutout with a regulator and maybe not wired up right. Check it out and let us know how you are doing.


Follow Ups:




Post A Followup

:
:

: Re: Re: Re: Farmall H generator

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Third Brush Generators - by Chris Pratt. While I love straightening sheet metal, cleaning, and painting old tractors, I use every excuse to avoid working on the on the electrics. I find the whole process sheer mystery. I have picked up and attempted to read every auto and farm electrics book with no improvement in the situation. They all seem to start with a chapter entitled "Theory of Electricity". After a few paragraphs I usually close the book and go back to banging out dents. A good friend and I were recently discussing our tractor electrical systems when he stated "I figure it all comes back to applying Ohms Law". At this point ... [Read Article]

Latest Ad: John Deere B 1943 [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy