FREE SHIPPING on orders above $249.99! Details

• Tractor Parts

• Engine Kits

• Carburetors

• Salvage

• Manuals

• DVDs

• Hats

• Contact Us

• Shipping Rates

• Return Policy

• Ordering Help

• Company Info

• Parts Warranty

• Forums

Ford 8160 Tractor Parts

[Categories] [All Ford Models] [Print]

Cooling System

No
Picture
Water Pump - Fits Ford New Holland models: 8160, 8260, 8360, 8560, TM115, TM125, TM135, TM150, TM165 (Item #: 113445, Ref: 82847714) $169.00

Drive Train

$Ford 8160 Forward \ Reverse Shift Cable$
Forward / Reverse Shift Cable - Used on Ford / New Holland models 8160, 8260, 8360, TM115, TM120, TM125, TM130, TM140. For Mechanical Gear Box with 20 x 16 or 16 x 16 Transmission, 54 Inches over all length. (Item #: 167816, Ref: 82006918) $52.00

Oil Pressure Switch - This Transmission Pressure Switch Thread has M12 x 1.5mm fitting. It is used in multiple Ford/New Holland, Case/IH and Fiat models. Replaces part numbers 5115055, 79043250, 82030730, 82031395, 87395493 (Item #: 164118, Ref: 82031395) $24.30

Electrical System

Alternator - 12 volt, 100 amp. For tractor models (5640SLE 1994-97 with 4-268 dsl), (6640SLE, 7740SLE 1994-97 with 4-304 dsl), (7840SLE 1994-97 with 6-401 dsl), (8160 1996-98 with 6-456 dsl), (8240SLE, 8340SLE 1994-97 with 6-456 dsl), (8260, 8360, 8560 1996-98 with 6-456 dsl). All Marelli equipped. Replaces 63321285. (Item #: 112402, Ref: ALU0008) $198.00

Alternator - 12 volt, 100 amp. For tractor models 8160, 8260, 8360, 8560. Replaces 82002329. (Item #: 82010243) $310.65

Blower Motor - Blower motor only, original Fasco replacement motor, 12 volt single speed 2 wire motor with 5/16 inch shafts. TM115, TM120, TM125, TM130, TM135, TM140, TM150, TM155, TM165, TM175, TM190, TS90, TS100, TS110, TS115, 8160, 8240, 8260, 8340, 8360, 8560, 5640, 6640, 7740, 7840. (Item #: 170462, Ref: 81870361) $92.00

No
Picture
Relay - Switch, Relay for Headlamp Wiring Harness. For tractors~ E series backhoe 3010S, 4010S, 8160, 8260, 8360, 8560, TM115, TM125, TM135, TM150. For 3010S, 4010S, 8160, 8260, 8360, 8560, TM115, TM125, TM135, TM150. (Item #: 115683, Ref: 82003697) $13.50

Relay - Ignition Load - For Ford tractor models 3430, 3930, 4130, 4630, 4830, 5030, 5640, 6640, 7740, 7840, 8160, 8240, 8260, 8340, 8360, 8560 Replaces Ford OEM number 83990084, 81AG14N089CA, , Compatible with New Holland tractor models TM115, TM120, TM125, TM130, TM135, TM140, TM150, TM155, TM165, TM175, TM190, TS90, TS100, TS110, TS115, Replaces New Holland OEM number 83990084, 81AG14N089CA, (Item #: 155403) $16.40

No
Picture
Starter - Bosch Style (18034), Used - For Ford tractor models 7840, 8160, 8240, 8260, 8340, 8360, 8560 Replaces Ford OEM number F1NN11000AA, , Compatible with New Holland tractor models 7840, 8010, 8160, 8240, 8260, 8340, 8360, 8560, Compatible with New Holland Skid Steer Loader(s) L781, L783, L785, L865, LS180, LS190, LX985, Compatible with New Holland Hay Cutting(s) HW340, Replaces New Holland OEM nos 82005343, 81868126, Replaces Bosch Mfg nos 0-001-369-200, 0-001-369-201, Replaces Mfg nos 18034, 3.6 kw, Voltage: 12, Rotation: Clockwise, Teeth: 10, Mounting Holes: 3, For a new version of this item use Item #: 117730, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 407730) $105.01

Starter New - Starter Assembly. Replaces F0NN11000CA and 9821291, 3.1 kw. For 4830, 5030, 555C, 555D, 555E, 5610S, 5640, 575D, 575E, 655C, 655D, 655E, 6610S, 6640, 675D, 675E, 7610S, 7840, 8160, 8240, 8260, 8340, 8360, 8560, L865, L885, LX865, LX885, TS100, TS110, TS90. (Item #: 113233, Ref: 82005342) $165.00

Starter Switch - Ignition Switch Assembly, Starter/Heater. Tractors: 5640, 6640, 7740, 7840, 8160, 8240, 8340, 8360, 8560, TM115, TM125, TM135, TM150, TM165, TS90, TS100, TS110. (Item #: 156344, Ref: F0NN11N501AA) $43.70

Engine Bearings

Main Bearings - .010" Oversize - Set - For Ford tractor models 7840, 8160, 8240, 8260, 8340 (8/93 - earlier), 8360, 8560, 8670, 8770, 8870, 8970, Compatible with Ford Engine (s) 401, 456T Replaces Ford OEM number 87790346, 87790364, , Compatible with New Holland tractor models 8010, 8160, 8240, 8260, 8360, 8560, Replaces New Holland OEM number 87790364, 87790346, Sold in complete set, Bearing Size: .010" Oversize, Full groove upper with slot and .370" oil hole, For Standard main bearing use Item #: 106427, (Item #: 106425) $105.00

Main Bearings - .020" Oversize - Set - For Ford tractor models 7840, 8160, 8240, 8260, 8340 (8/93 - earlier), 8360, 8560, 8670, 8770, 8870, 8970, Compatible with Ford Engine (s) 401, 456T Replaces Ford OEM number 87790345, 87790365, , Compatible with New Holland tractor models 8010, 8160, 8240, 8260, 8360, 8560, Replaces New Holland OEM number 87790365, 87790345, Sold in complete set, Bearing Size: .020" Oversize, Full groove upper with slot and .370" oil hole, For Standard main bearing use Item #: 106427, (Item #: 106426) $106.00

Main Bearings - .030" Oversize - Set - For Ford tractor models 7840, 8160, 8240, 8260, 8340 (8/93 - earlier), 8360, 8560, 8670, 8770, 8870, 8970, Compatible with Ford Engine (s) 401, 456T Replaces Ford OEM number 87790346, 87790366, , Compatible with New Holland tractor models 8010, 8160, 8240, 8260, 8360, 8560, Replaces New Holland OEM number 87790366, 87790346, Sold in complete set, Bearing Size: .030" Oversize, Full groove upper with slot and .370" oil hole, For Standard main bearing use Item #: 106426, (Item #: 106427) $107.00

Main Bearings - Standard - Set - For Ford tractor models 7840, 8160, 8240, 8260, 8340 (8/93 - earlier), 8360, 8560, 8670, 8770, 8870, 8970, Compatible with Ford Engine (s) 401, 456T Replaces Ford OEM number 87790342, 87790362, , Compatible with New Holland tractor models 8010, 8160, 8240, 8260, 8360, 8560, Replaces New Holland OEM number 87790362, 87790342, Sold in complete set, Bearing Size: Standard, Full groove upper with slot and .370" oil hole, For .010" main bearing use Item #: 106427, (Item #: 106424) $116.00

Engine Gaskets

Crank Seal, Front - Fits 3, 4 and 6 Cylinder Engines in: 2000, 2600, 3000, 3600, 3610, 3910, 4000, 4600, 4610, 5000, 5600, 5700, 6000, 6600, 6610, 6640, 6700, 6710, 7000, 7600, 7610, 7700, 7710, 8000, 8160, 8200, 8240, 8260, 8340, 8360, 8560, 8600, 8700, 9000, 9200, 9600, 9700, TS80, TS90, TW10, TW20, TW30. 60MM X 89MM X 12MM. Replaces 81813951, 81815927, 83999512, 1815927, F0NN6700CA, 83908809, 87800348, 87800696, 87802755, C5NN6700A, D5NN6700A (Item #: 106352, Ref: D5NN6700A) $9.00

Engine Parts

Crankshaft Pulley Spacer - Used on many Ford / New Holland models, 1965 and later, this is a keyed spacer. It fits behind the crankshaft pulley. Replaces OEM part numbers 83995427, 1811427, 81811427, C5NE6B306A, C5NE6C306A (Item #: 154924, Ref: C5NE6B306A) $20.30

Exhaust Valve - For Ford tractor models 5610 (S), 6610 (S), 6810 (S), 7610 (S), 8160 (S), 8260 (S), 8360 (S), 8560 (S), Compatible with Ford Construction and industrial models 555E, 575E, 655E, 675E Replaces Ford OEM number 81865088, 82850523, F0NN6505AD, , Compatible with New Holland tractor models TB80, TB85, TM115, TM125, TM135, TM150, TM165, TS90, TS100, TS110, Compatible with New Holland Construction and industrial models LB115, Replaces New Holland OEM number 81865088, (Item #: 166415) $11.20

Freeze Plug - Used on Ford / New Holland tractors 1965 and later, this freeze plug is 1.18 inches in diameter (Item #: 173014, Ref: 390625S) $2.10

No
Picture
Head Bolt Kit - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 7810, 7840, 7910, 8160, 8210, 8240, 8260, 8340, 8360, 8530, 8560, 8630, 8670, 8700, 8730, 8770, 8830, 8870, 8970, 9700, Replaces Ford OEM number 87802206, 87802207, 9/16" Bolts, (Item #: 166230) $153.00

No
Picture
Intake Valve - For Ford tractor models 5610S, 5640, 6610, 6640, 6810, 7610, 7810S, 7840, 8160, 8240, 8260, 8340, 8360, 8560 Replaces Ford OEM number VPA7270, , Compatible with New Holland tractor models TS80, TS90, 7010, 8010, Replaces New Holland OEM number 81865092, (Item #: 176503) $16.70

Valve Lifter, Used - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 2000, 2310, 2610, 2810, 3000, 3230, 3430, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 4600, 4610, 4630, 4830, 5000, 5030, 5110, 5600, 5610, 5640, 5700, 5900, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7000, 7410, 7600, 7610, 7700, 7710, 7740, 7810, 7840, 7910, 8000, 8160, 8200, 8210, 8260, 8340, 8360, 8530, 8560, 8600, 8630, 8700, 8730, 8830, 9000, 9600, 9700, Compatible with Ford Construction and industrial models 550, 555, 555E, 575E, 655, 655E, 675E, Compatible with Ford Engine(s) BSD326, BSD329, BSD332, BSD333, BSD442, BSD442T, BSD444, BSD444T, BSD666, BSD666T Replaces Ford OEM number C7NN6500B, C5NE6500C2, 83946434, E4HN6500AA, 83957729, C5NE6500C, , Compatible with New Holland tractor models TB90, TB100, TB110, TB120, TS80, TS90, 7010, 8010, 8240, For a new version of this item use Item #: 112190, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 435585) $4.76

Exhaust System

Muffler - This New Muffler is used on Ford / New Holland models: 8160, 8260, TM115, TM120, TM130. It replaces original part numbers 47729203, 82010813 (Item #: 182993, Ref: 82010813) $353.00

Fuel System / Air Intake

Air Filter, Inner - Top outside diameter 3.59 inches, bottom outside diameter 4.33 inches, top inside diameter .43 inches, bottom inside diameter 3.00 inches, height 11.42 inches. For tractor models 7840, 8240, (8340 up to 9/1993 Non Turbo), 8160, 8260, 8360, 8560. (Item #: 125958, Ref: 82008601) $71.00

Air Filter, Outer - Top outside diameter 8.62 inches, bottom outside diameter 7.43 inches, top inside diameter .43 inch, bottom inside diameter 3.77 inches, height 13.05 inches. For tractor models 7840, 8240, (8340 up to 9/1993 Non Turbo), 8160, 8260, 8360, 8560. (Item #: 125959, Ref: 82008600) $77.00

No
Picture
Fuel Filter - Fuel Water Separator Cartridge (PRIMARY). Tractors: 8160, 8260, 8360, 8560, M100, M115, M135, M135DT, M160, M160DT, M150. (Item #: 182563, Ref: 87840591) $23.60

Gauges

Temperature Sender - Temperature Sender, Water. The part may come with a spade terminal which might require changing your wire end. 3/8 Inch NPT Thread.Replaces: 81818428, 83904449, 83904448, 81837742, 83911735, 83948391, 8712608, 82028131, 9712608, D8NN10884AA, E1NN10884AA, 2080406, 3917490, 73403367 (Item #: 128314, Ref: D5NN10884A) $11.31

Hitch / Drawbar

Straight Rear Drawbar - For Ford tractor models 8160, 8210, 8260, 8360, 8560 Replaces Ford OEM number E3NN805AA12B, , Compatible with New Holland tractor models TS90, TS100, TS110, TS115, Replaces OEM number SW03631, SW82010158, 3" Wide, 1.375" Thick, 41.75" Long, (Item #: 155691) $198.00

Hydraulic System

Hydraulic Filter Spin-On, Intake - Outside diameter 5.38 inch, inside diameter 1.75 inch, height 9.62 inch. For tractor models 6510S, 6610S, 7610S, 8010, 5640, 6640, 7740, 7840, 8240, 8340, 8160, 8260, 8360, 8560. Replaces F0NNB486BB. (Item #: 126239, Ref: 82005016) $55.07

Hydraulic Pump - This is a new Bosch A31XRP2 typed Hydraulic Pump used on Ford / New Holland models: 4835, 5635, 6635, 7635, 8160, 8260, 8360, TL100, TL100A, TL70, TL80, TL80A, TL90, TL90A, TN55, TN55D, TN55S, TN60A, TN60DA, TN60SA, TN65, TN65D, TN65F, TN65S, TN70, TN70A, TN70D, TN70DA, TN70F, TN70S, TN70SA, TN75, TN75A, TN75D, TN75DA, TN75F, TN75FA, TN75S, TN75SA, TN80F, TN90F, TN95F, TN95FA. This pump replaces 5180275, 5167394 (Item #: 168782, Ref: 5180275) $237.00

Hydraulic Pump Assembly - Dynamatic - For Ford tractor models 8160, 8260, 8360, 8560 (all chasis D3711-later), Replaces Ford OEM number 82013741, 82007671, Genuine Dynamatic pump, Manufactured to exact OEM specifications, To validate your warranty: A contaminated system should be completely flushed by an authorized dealer. Use new, clean fluid and filters, Item ships via freight carrier please call 1-800-853-2651 for a freight quote, (Item #: 157823) $3999.01

RH Leverless Hydraulic Coupler, Used - For Ford tractor models 8160, 8260, 8360, 8560, Right Hand, With 4 Mounting Bolts, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 430670) $263.01

Miscellaneous

Hydraulic Valve - For Ford tractor models TW5, TW15, TW25, TW35, 2310, 2810, 2910, 3230, 3430, 3610, 3910, 3930, 4110, 4130, 4610, 4630, 4830, 5030, 5110, 5610, 5640, 5900, 6410, 6610, 6640, 6710, 6810, 7410, 7610, 7710, 7740, 7810, 7840, 7910, 8160, 8210, 8240, 8260, 8340, 8360, 8560, 8630, 8730, 8830, Compatible with Ford Construction and industrial models 230A, 234, 334, 335, 345C, 345D, 445C, 445D, 530A, 545C, 545D, Compatible with New Holland tractor models TS90, TS100, 6810S, 7010, 7610S, 8010, Replaces OEM number 81864874, 82988269, E2NNB950AC11B, E9NNB950BB, (Item #: 121955) $897.00

Thermostart Plug - Intake Manifold Heater. For tractor models 230A, 234, 250C, 260C, 2610, 2810, 2910, 3430, 345C/D, 3610, 3910, 3930, 4110, 445/A/C/D, 4610, 4630, 545/A/C/D, 5610, 6610, 6710, 7610, 7710, 7810, L783, L785, 3230, 4130AP, 4830, 5030, 5640, 6640, 7010, 7740, 7840, 8010, 8240, 8340, L865, L885, LX865, LX885, 334, 335, 550, 2310N, 530A, 5110, 6810, 8160, 8260, 836, 856. Replaces 80858863, 83933675, 87800843, C5NE9A436A, E1NN9A436AA, 603922 (Item #: 118792, Ref: 3583543M2) $10.90

Oil System

Oil Pan Drain Plug - This 3/4 inch Oil Pan Drain Plug is for Ford tractor models: 230A, 231, 233, 234, 333, 334, 335, 420, 445, 445A, 450, 515, 531, 532, 535, 540, 540A, 540B, 545, 545A, 550, 555, 555A, 555B, 555C, 555D, 575D, 655, 655A, 655C, 655D, 755, 755A, 755B, 2000, 2600, 2910, 3000, 3230, 3400, 3430, 3500, 3550, 3600, 3610, 3900, 3910, 3930, 3500, 3550, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4110LCG, 4130, 4400, 4500, 4610, 4630, 4830, 5000, 5030, 5500, 5550, 5600, 5610, 5900, 6500, 6600, 6610, 6700, 6710, 7000, 7500, 7600, 7610, 7700, 7710, 7810, 7810S, 7840, 7910, 8000, 8010, 8160, 8210, 8240, 8260, 8340, 8360, 8530, 8560, 8600, 8630, 8670, 8700, 8730, 8770, 8830, 8970, 9000 1970 and up. Uses C9NN6734A washer, not included. Replaces C9NN6730B. (Item #: 140610, Ref: C9NN6730B) $3.40

Oil Pan Drain Plug Washer - Used with C9NN6730B 3/4 inch Oil Pan Drain Plug. Fits models: 230A, 231, 233, 234, 333, 334, 335, 420, 445, 445A, 450, 515, 531, 532, 535, 540, 540A, 540B, 545, 545A, 550, 555, 555A, 555B, 555C, 555D, 575D, 655, 655A, 655C, 655D, 755A, 755B, 2000, 2110LCG, 2600, 2810, 2910, 3000, 3230, 3400, 3430, 3500, 3550, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4110LCG, 4130, 4400, 4500, 4610, 4630, 4830, 5000, 5030, 5500, 5550, 5600, 5610, 5900, 6500, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710, 7810, 7810S, 7840, 7910, 8000, 8010, 8160, 8210, 8240, 8260, 8340, 8360, 8530, 8560, 8600, 8630, 8670, 8700, 8730, 8770, 8830, 8970, 9000. (Item #: 140611, Ref: C9NN6734A) $1.60

Oil Pump - For Ford tractor models 7810S, 7840, 8160, 8240, 8260, 8340, 8360, 8560, 8670, 8770, 8870, 8970, Replaces Ford OEM number 81868538, E9NN6600BB, (Item #: 128690) $103.00

PTO / Driveline

PTO Shaft, Independant, 1000 RPM - 1-3/8 inch diameter, 21 spline. For tractor models 4030, 4230, 4330, 4835, 5530, 5635, 6530, 6635, 7530, 7635, 8160, 8260, 8360, 8560. Replaces 5185601. (Item #: 158009, Ref: 5149242) $250.00

PTO Shaft, Independant, 540 RPM - 1-3/8 inch diameter, 6 spline. For tractor models 4030, 4230, 4330, 4430, 4835, 5530, 5635, 6530, 6635, 7530, 7635, 8160, 8260, 8360, 8560, TN65F, TN75F, TN90F Replaces 5185602, 5149243, 4983660, 05185602. (Item #: 152618, Ref: 5149243) $144.00

Sheet Metal / Body Parts

Battery Support Tray - This Battery Support Tray is used on 4WD models: 8160, 8260, 8360, 8560, TM115, TM125, TM135, TM150, TM165 (Item #: 162162, Ref: 82018950) $59.00

No
Picture
Grille - For Ford tractor models 8160, 8260, 8360, 8560 Replaces Ford OEM number 82016094, , Compatible with New Holland tractor models TM115, TM120, TM125, TM130, TM135, TM140, TM150, TM155, TM165, TV140, 8160, 8260, 8360, 8560, Replaces New Holland OEM number 82016094, Comes primered (color may vary). Prior to painting check fitment, Additional Handling and Oversize Fees Apply To This Item, (Item #: 159296) $430.00

Side Panel - Left Hand - For Ford tractor models 8160, 8260, 8360, 8560 Replaces Ford OEM number 87336883, 87376528, 82003526, 82022570, , Compatible with New Holland tractor models TM115, TM120, TM125, TM130, TM135, TM140, TM150, TM155, TM165, TM175, TM190, TV140, TV145, 8160, 8260, 8360, 8560, Replaces New Holland OEM number 87376528, 82003526, 82022570, 87336883, Fits Left Hand Side, For right side use Item #: 169618, (Item #: 169617) $100.00

Side Panel - Right Hand - For Ford tractor models 8160, 8260, 8360, 8560 Replaces Ford OEM number 87336881, 87376530, 82003525, 82030884, 82023132, 82022899, 82035294, , Compatible with New Holland tractor models TM115, TM120, TM125, TM130, TM135, TM140, TM150, TM155, TM165, TM175, TM190, TV140, TV145, 8160, 8260, 8360, 8560, Replaces New Holland OEM number 87376530, 82003525, 82030884, 82023132, 82022899, 82035294, 87336881, Fits Right Hand Side, For left side use Item #: 169617, (Item #: 169618) $100.00

Steering

King Pin Thrust Bearing - Used on Carraro 4WD Axles, this King Pin Thrust Bearing (Trunion Bearing) replaces OEM numbers 5119699, 05119699, TX51785, OSA 206S, OSA206S (Item #: 156139, Ref: 5119699) $67.00

Planetary Gear - For Ford tractor models 5640, 6640, 7530, 7740, 7840, 8160, 8240, 8260, 8340, Compatible with New Holland tractor models T6010, T6020, T6030, T6040, T6050, T6060, T6070, T6080, TM115, TM120, TM125, TM130, TM135, TM140, TS90, TS100, TS100A, TS110, TS110A, TS115, TS115A, TS125A, TS130A, TS135A, Replaces New Holland OEM number 5145501, (Item #: 156055) $86.00

No
Picture
Planetary Sun Gear, Used - For Ford tractor models 5640, 6640, 7530, 7740, 7840, 8160, 8240, 8260, 8340, Compatible with New Holland tractor models T6010, T6020, T6030, T6040, T6050, T6060, T6070, T6080, TM115, TM120, TM125, TM130, TM135, TM140, TS90, TS100, TS100A, TS110, TS110A, TS115, TS115A, TS125A, TS130A, TS135A, Replaces New Holland OEM number 5145501, For a new version of this item use Item #: 156055, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 455942) $66.01

Roller Bearing - Used in many Four Wheel Drive Systems, this bearing measures 109.5mm (4.311 inches) inside diameter, 158.8mm (6.25 inches) outside diameter and 21.2mm (o.834 inches) wide. Replaces OEM numbers ZP0735370150, 81676C1, 84592016, 47724311, 5133737, 83952531, K395101, H1482196, CAR118370, 9967690, CAR045180, CAR142088, K395101, ZP0735370150, 83952531, 47724311, 5133737, 84592016, 6914441, 9967690, 83985020, 89967690, CAR118370, 81676C1, 05133737, 47724311, H1482196, K395101, 81676C1 (Item #: 156047, Ref: JD10249) $83.00

Taper Roller Bearing - Measuring; Width - 0.548 inches, Inside Diameter - 3.740 inches, Outside Diameter - 5.315 inches, this bearing is used in ZF Axles on tractors with mechanical four wheel drive. This bearing also has other applications. Replaces OEM numbers: ZP0750117062, 5136951, 83946047, 81312C1, 83927807, 47539809, 1-31-741-019, 05136951, 85136951, 85806002, 1966169C1, CAR118378, 83983456, AL38099, RE45944, 819310, 819349/819310, 819349 (Item #: 156177, Ref: ZP0750117062) $86.82

Tie Rod Assembly - This Tie Rod Assembly is 60.38 inches long. It replaces 5168941 Used on Ford / New Holland 8160 (1/95 - later), 8240 (1/95 - later), 8260 (1/95 - later), 8340 (1/95 - later), TM115, TM120, TM125, TM130, TM135, TM140, TS100A, TS110A, TS115A, TS125A (Item #: 104663) $244.00

Tie Rod End - For Ford tractor models 8160, 8260, 8360, 8560, Compatible with New Holland tractor models TM115, TM120, TM125, TM130, TM135, TM140, TM150, TM155, TM165, 8160, 8260, 8360, 8560, Replaces OEM number 5178344, Dimension A: 35.500", Dimension B: 1.250", (Item #: 104695) $117.00

Tie Rod End - For Ford tractor models 8160, 8260, 8360, 8560, Compatible with New Holland tractor models TM115, TM120, TM125, TM130, TM135, TM140, TM150, TM155, TM165, 8160, 8260, 8360, 8560, Replaces OEM number 5178338, Dimension A: 4.625", Dimension B: M32 x 1.5 Right Hand Thread, (Item #: 104696) $65.00

Universal Parts and Accessories
Category: Accessories / Supplies

Accessories / Supplies

Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $385.00

Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $97.00

Cooling System

Thermostat Housing to Block Gasket - Tractors: all 4-cylinder, 1953-1964, gas and diesel. Bolt holes measure 3/8 inch in diameter, and center to center of bolt hole spacing is 2 3/4 inches. Sold and Priced as Each. (Item #: 191970, Ref: EAF8255A) $5.20

Decals and Emblems

Decal, Fear This Ford - 12-1/2 inches x 3 inches. For all Ford tractors. (Item #: 183476, Ref: S.67825) $15.80

Sherman Transmission Instruction Plate - For Ford models with Sherman step up step down transmission. Installs under steering wheel nut. (Item #: 178113, Ref: SHERMAN) $20.20

Drive Train

Shift Cover Plate Gasket - For all models with 5-SPEED transmission built between 1955-1964. Not for tractors made overseas, such as Major, Dexta, etc. (Item #: 178105, Ref: NDA7223A) $6.40

Electrical System

NOTE

Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.

NOTE

No
Picture
Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $96.00

Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $14.40

Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20

No
Picture
Battery Thermal Wrap - 60 Watt, 28 inches long wrap to keep your battery warm. (Item #: BTW28) $35.98

No
Picture
Battery Thermal Wrap - 160 Watt, 36 inches long wrap to keep your battery warm. (Item #: BTW72) $53.81

No
Picture
Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $49.20

No
Picture
Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60

Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $4.80

NOTE

Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!

NOTE

Starter Solenoid, 12 Volt - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. (Item #: 150223, Ref: DR1467) $19.20

Switch, Push Button - This 2 terminal switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch overall length. Check measurements before ordering if using as a universal part. Applications include ether switch, horn button, cold start, starter switch, and manifold heater switch. It replaces 22702, 240962, 242988, 245866, 245936, 70253322, 71191589, 72160068, VT507, 86900358, A30858, O9995AB, T18524, TG07803, TO18117, TO7803, 271179R91, 367678R91, 373611R91, 393209R91, AR46184, AR47373, AR47374, R39554, 189158M91, 767828M91, 105386A, 10A972, 1K7392C, UT2421, 1K7392A, 7A7392. (Item #: 121141, Ref: R7994) $13.40

Engine Gaskets

Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.90

Engine Parts

NOTE

Valve Overhaul Kits - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor).

NOTE

Engine Pistons and Sleeves

No
Picture
Seal Kit - Seal kit, for cylinder E2NN3A540BA. Piston rod is retained with 1" snap ring and 1-3/4" threaded spanner nut. (Item #: E2NN3X-SK) $64.99

Engine Rings

NOTE

Piston Ring Sets - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size and type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32"), 4. Number and size of oil rings for each piston (Ex: (1) 5/32").

NOTE

Exhaust System

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $81.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $108.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $135.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $106.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $161.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $145.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00

Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00

$Ford 8160 Muffler Clamp, 1-1\4$
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $2.10

$Ford 8160 Muffler Clamp, 1-3\4$
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80

$Ford 8160 Muffler Clamp, 1-3\8$
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.90

$Ford 8160 Muffler Clamp, 2-1\4$
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $5.30

$Ford 8160 Muffler Clamp, 2-3\4$
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71

Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.40

$Ford 8160 Muffler Clamp, 3-1\2$
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $8.00

Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.30

Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $12.70

Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $11.00

Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $8.80

Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $12.50

Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.08

Rain Cap - This rain cap is for a 4.00 inch pipe. (Item #: 108645, Ref: R1807) $12.90

Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.40

Rain Cap - This rain cap is for a 5.00 inch pipe. (Item #: 108750, Ref: WC15) $17.40

Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $6.50

Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $8.50

Fuel System / Air Intake

Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $14.00

Filter Screen and Gasket for Sediment Bowl - 1-1/2 inch outside diameter seal (for a 1 9/16 inside diameter housing and a 1 3/8 inch outside diameter screen. Measure before ordering. For tractor models (1958-1964 All with 134 cubic inch engines), 2000 4 cylinder, 501, 601, 701, (1958-1960 all with 172 cubic inch engines up to 126524), 801, 901, 1801. (Item #: 150700, Ref: ABC346) $5.70

Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.92

Gauges

Ammeter, Black, Flat Bezel - For all models to 1958. Terminal type ammeter. 30-0-30. Black ring. Replaces FAD10850A. (Item #: 110410, Ref: A0NN10670A-BLAC) $10.70

No
Picture
Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $63.00

Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $42.30

Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar

Drawbar Check Chain Kit - This Drawbar Check Chain Kit includes: right hand/left hand anchors, 2 eyelets, 2 chains, 4 clevis with pins, and hardware. Fits: Jubilee, NAA, NAB, 2000 3 Cylinder, 2000 4 cylinder, 2600V, 2N, 3600V, 4000 4 Cylinder, 501, 600, 601, 700, 701, 800, 801, 8N, 900, 901, 2030, 2031, 2100, 2110, 2111, 2120, 2121, 2130, 2131, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3110, 3120, 3300, 3330, 3600, 3610, [4030, 4130, 4140 (4 cylinder)], 4031, 4040, 4100, 4110, 4120, 4121, 4131, 9N, Industrial: 231, 233, 333, 334, 335, 1801, 1811, 1821, 1841, 1871, 1881, 230A, 3400, 3500, 530A, Dexta, Super Dexta. Replaces: 957E597, 957E596, CBPN598A, NCA597B, NCA596B. (Item #: 115051, Ref: NCA596B) $40.60

Drawbar, Heavy Duty, Heat Treated - Standard Heat Treated Drawbar Red, 30 1/2 inch L hole center to hole center, 2 1/2 inch wide, 1 1/8 inch thick (drawbar fits lift between lift arms). (Item #: 103174, Ref: 9N5182) $42.10

Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $11.40

Link End - Plated, forged, 1-1/4 inch thread, left hand, 1 inch hole. (Item #: 180473, Ref: RE1717L) $19.00

Link End - Plated, forged, 1-1/4 inch thread, right hand, 1 inch hole. (Item #: 174507, Ref: RE1718R) $20.90

Stabilizer Arm HD - Arm only, made of alloy spring steel, for kit 231253XHD, red only. 7/8 inch hole diameter. 31 1/2 inches center to center. (Item #: 110516, Ref: 230042XHD) $15.20

Top Link - Forged Top Link, 12 inch body, Category I implement ends. Adjusts 17.5 to 24 inches overall. 3/4 inch pin holes and both eyelets are 1 3/4 inch wide. Dichromate plated. (Item #: 103162, Ref: JSA1012C) $20.00

Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System

Coupler Flange - FORD: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. Hydraulics: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. 2-1/4 inch b-b (Item #: 108772, Ref: L36-6) $64.00

Coupler Flange - Drive flange; 3/4 inch round bore with set screw 1/4 inch x 3/8 inch. 1-15/16 inch spacing. For Morflex series 302. Replaces: L363, 191061, 1752219M91, L36-3 (Item #: 112104, Ref: 191061) $22.00

Coupler for Pump Shaft - The Hydraulic Pump Shaft Coupler is 1-1/2 Outside Diameter and 2-1/4 inches long. It 7/8 inch 13 splined inside. It replaces 1631413, 350-1631413, S340 (Item #: 114586, Ref: S340) $36.00

Coupler Hub Drive Kit - Coupler Complete, Morflex Series 302. Contains center member, 2 drive flanges with set screws, and 4 bolts with lock nuts. The center member is 3-1/8 inch diameter, with four 1/4 inch holes and 1-15/16 inch spacing.The drive flange is 3/4 inch round bore with set screw 1/4 inch by 3/8 inch. (Item #: 112067, Ref: L601-14) $124.00

Cylinder Seal Kit, For 2 inch cylinders - For TISCO side and top link replacement cylinders. Seal Repair Kit for 2 inch cylinders. For cylinder numbers: HTL2101, HTL2102, HTL2103, HSL2201, HSL2202, HSL2203. Replaces HSK2001. (Item #: 183971, Ref: HSK2002) $24.50

Cylinder Seal Kit, For 3 inch Cylinders - For TISCO brand side and top link replacement cylinders ONLY. Seal Repair Kit for 3" cylinders. For cylinder numbers: HTL3101, HTL3102, HTL3103, HSL3201, HSL3202, HSL3203. Replaces HSK3001. (Item #: 179480, Ref: HSK3002) $32.10

Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.40

Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.60

Hub - 7/8 inch, 13 spline threaded, 3-7/8 inch hole spacing. For 730 LOADER. Used with C5NNN879A hub. (Item #: 160204, Ref: 291315) $65.00

Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00

Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50

Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.10

Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10

Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50

Hydraulic Pump Drive Flange - The bolt holes on the flange are 5/16 inches diameter and 2.250 center to center. This is used on a drive shaft that is 3/4 inches in diameter with a key way and set screw. This part replaces 1753730M1, 192199, 192199GV, L367GV, L36-7GV, 1753730M1GV, 1753730M91, L367. It is part of a 352 series Morflex Coupler. (Item #: 128567, Ref: 192199) $21.10

Hydraulic Pump for Loader - Part Description: Pump, Hydraulic For 730 LOADER, 735 LOADER. SPECS: CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIAMETER: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: Left hand, PORT SIZE INLET: 1-5/8 inches-12 ORB, PORT SIZE OUTLET: 1-5/16 inches-12 ORB, MOUNTING: 2 bolt SAE "B", FORD PUMP APPLICATION: 730 and 735 loaders, CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIAMETER: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: Left hand, MOUNTING: 2 bolt SAE "B", INLET: 1-5/8 inches-12 ORB, OUTLET: 1-5/16 inches-12 ORB. The 2 bolt mount slots are 9/16 inch and open on the ends. Minimum measurement between the slots are 5 1/4 inches and Maximum is 6 7/8 inches. (Item #: 127269, Ref: 7702425-29Z) $780.00

Hydraulic Pump, Front Mounted - This Hydraulic Pump is used with some 701, 702 and 703 Loaders. It is 14 Gallons Per Minute at 2000 RPM. The shaft is 3/4 inch round with a key way. Left Hand Rotation. Inlet is 1 Inch NPT. Outlet is 3/4 Inch NPT. Mounting bolt spacing 4 3/16 inches center to center. Comes with two adapters. Contains: 1-720FSO-3/4X3/4 HC4008 adapter, 1-720FSO-1X1-1/4 HC4009 adapter. This Pump may work in other loader application. Verify Specs before ordering. (Item #: 182700, Ref: L827-10X-LB) $600.00

Hydraulic Valve Kit - Valve with handles, three-spool, 2000 p.s.i. Relief, all spools tandem (4-way) spring center to neutral. (Item #: HV4030) $787.98

LBP Coupler Center - Center member. Center member. 3-5/8" O.D., four 5/16" holes, 2-1/4" bolt circle (L52-10) For tractor models 352. (Item #: 178931, Ref: 192169) $75.00

LBP Hydraulic hose Assembly - Hydraulic hose assembly. For Ford model 740 LOADER. (Item #: 179521, Ref: 7701142) $30.30

Morflex Center Member - This is a 1-302 Morflex Center member. It measures 3-1/8 inch diameter, four 1/4 inch holes, 1-15/16 inch bolt circle. Replaces part numbers 893129, 191192, L5227, 1506097M91, 1086870M1, 191192LBP, 1752218M91, L52-27 (Item #: 116952, Ref: 191192LBP) $49.00

Top Link, Hydraulic - FORD: Hydraulic top link cylinder. All ports 9/16 inch-18 O-ring boss with two adapters 9/16 inch-18 ORBM x 1/4 inch NPTM 90 degree swivel. 3 inch cylinder bore, 8 inch stroke length, 26 inch closed length, 12-7/16 inch barrel length, 1 inch rod end diameter, 1-3/4 inch rod end width, 1 inch diameter base end. (Item #: 167145, Ref: HTL3103) $270.00

Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $13.50

Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $13.91

Implements

Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.90

Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.90

Bearing Cup - This part fits Caster Assembly (Part Number BH215, Ref #6). Sold individually, two used per caster assembly. Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. Also replaces 132709, 15191, 32190M1, L44610. (Item #: 169771, Ref: 170BH) $7.86

Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly uses 1 1/2 inch diameter shaft. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00

Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $132.00

Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.10

Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.30

No
Picture
Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $51.00

No
Picture
Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48

No
Picture
Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54

No
Picture
Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $78.00

No
Picture
Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61

Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30

Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $56.00

No
Picture
Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.10

Lights

Headlight Assembly, 12 Volt - (Single) Headlight Assembly 12-volt, blue - Sealed beam headlamp assembly in heavy gauge steel housing with Rubber bezel. Does not look like original. (Item #: 184496, Ref: L525HB-12V) $53.00

Light Switch with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60

Portable Halogen Work Lamp - 3 inch x 5 inch sealed beam unit, 12 volt, 50 watt, 4 amp. With handle and magnetic base. Projects flood beam pattern 50 foot wide x 30 foot long. Lamp is not legal for street use. (Item #: L200MAGH) $75.13

No
Picture
Sealed Beam Bulb, 12 Volt - Red/white combination work/tail light, 4-1/2 inch diameter. (Item #: 116014, Ref: S.52670) $23.50

Tail Light Lens - Plastic 4 inch lens for DUOLAMP with FOMOCO stamped on lens (has 2 mounting screw holes spaced 3 1/8 inches apart). Fits tractors 1953 and newer. (Item #: 178144, Ref: FDV13450A) $16.50

Miscellaneous

Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00

Hand Cleaner, Gallon - Hand cleaner, with dispenser pump. 1 gallon plastic bottle. (Item #: 180453, Ref: PRM25218) $24.60

Tractor Umbrella with Frame & Mounting Bracket - Blue - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without Additional Handling & Oversize Fees Apply To This Item, tools, (Item #: 161190) $123.00

Paint

44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00

No
Picture
Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.50

No
Picture
Paint, Brownish Medium Gray, 1 Quart - Ford Brownish Medium Gray was used for the same applications as TP240Ford Medium Gray. This is a lighter shade. Since the tractors did not come off the production line all the same, the darker or light shades are completely up to the desires of the customer. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184575, Ref: TP245QT) $50.00

No
Picture
Paint, Clear Coat, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $65.00

No
Picture
Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.00

No
Picture
Paint, Empire Blue, 1 Gallon - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100713, Ref: TP360GAL) $57.00

No
Picture
Paint, Empire Blue, 1 Quart - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100712, Ref: TP360QT) $24.00

No
Picture
Paint, Empire Blue, Spray Can - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100711, Ref: TP360SP) $7.70

No
Picture
Paint, Ford White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108135, Ref: TP470GAL) $86.00

No
Picture
Paint, Ford White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108133, Ref: TP470SP) $10.60

No
Picture
Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $53.00

No
Picture
Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $24.00

No
Picture
Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70

No
Picture
Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $22.40

No
Picture
Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100120, Ref: TP2700SP) $8.30

No
Picture
Paint, Industrial Yellow, Spray - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100723, Ref: TP760SP) $8.50

No
Picture
Paint, Light Gray, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100716, Ref: TP330GAL) $57.00

No
Picture
Paint, Light Gray, 1 Quart - OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100715, Ref: TP330QT) $21.40

No
Picture
Paint, Light Gray, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100714, Ref: TP330SP) $9.10

No
Picture
Paint, Medium Gray, 1 Quart - This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100718, Ref: TP240QT) $22.00

No
Picture
Paint, Medium Gray, Spray Can - This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100717, Ref: TP240SP) $8.50

No
Picture
Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $59.00

No
Picture
Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $24.00

No
Picture
Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $24.00

No
Picture
Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $8.50

No
Picture
Paint, Vibrant Blue, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156586, Ref: TP365GAL) $90.00

No
Picture
Paint, Vibrant Blue, 1 Quart - OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156587, Ref: TP365QT) $35.00

No
Picture
Paint, Vibrant Blue, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156585, Ref: TP365SP) $10.00

No
Picture
Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67

No
Picture
Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39

No
Picture
Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22

Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $40.01

PTO / Driveline

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $174.00

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00

NOTE

PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.

NOTE

PTO Overide Clutch - This 6 spline Override Coupler converts a 1 1/8 inch diameter PTO shaft to 1 3/8. It has a 1 1/8 inch female at one end and 1 3/8 inch male at the other end). Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 103169, Ref: C670F) $46.60

PTO Overide Clutch - Override coupler for 1 3/8 inch female to 1 1/8 inch male, 6-spline. Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 191020, Ref: C680F) $76.00

PTO Overide Clutch - Override coupler for 1 1/8 inch female to 1 1/8 inch male, 6-spline. Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 103167, Ref: C690F) $76.00

PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $268.00

Seats

Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056V) $1518.86

Seat, Air Suspension, Cloth, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with gray cloth upholstery, lumbar, recline tilt up and angle adjust armrests. * Trimmed in FabriForm cloth, can be punctured with pens and screwdrivers and will not tear. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056) $2161.57

Seat Cushion, Black - Cover with piping and Ford script logo. Fits all 1939-1964 models with a 17 inch wide steel seat pan. (Item #: 115058, Ref: 8N401BLK) $37.90

Tie-On Seat Cover - Blue and White, 19 inches wide. Deluxe with 2 inches of foam. (Item #: 101353, Ref: R1013) $31.30

Universal Seat - Color: Yellow - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. (Item #: 101375, Ref: TS1040ATSP) $100.00

Sheet Metal / Body Parts

Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Item #: 165963, Ref: R0140) $41.19

Pilot Punch Set - Set contains 12 sizes one of each 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16 and 1/2. (Item #: 186563, Ref: RPD112K) $173.00

Steering

Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417) $47.60

Steering Wheel Spinner Assortment - Complete wheel spinner assortment: includes 2 blue, 2 green, 3 red, 2 yellow and 3 black. (Item #: 185079, Ref: WSV125A) $128.00

Tie Rod Boot Assortment - Includes 6 Tie Rod Boots. Two each of the following sizes: 1 13/16 inches x 5/8 inch x 5/8 inch, 1 15/16 inches x 3/4 inch, 3/4 inch, and 1 3/8 inches x 1 inch x 1/2 inch. (Item #: 183427, Ref: TIERODBOOTS) $13.00

Tools

No
Picture
Blade Fuse Assortment - With 6-24 volt tester light and fuse puller. Contains 93 pieces. 5, 10, 15, 20, 25 and 30 amp blade type fuses. (Item #: 183798, Ref: S.29891) $23.10

No
Picture
Hay Moisture Tester - Self Calibrating Electronic Moisture Tester. (Item #: 180261, Ref: S.58474) $287.00

Tractor Manual Search - Yesterday's Tractor Co.

Wheels

Front Rim - This is a 6 inches x 16 inches Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Verify size of old rim before ordering. (Item #: 103768, Ref: FW60166) $92.00

Front Rim - This is a 5.5 inch x 16 inch Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Capacity of 3500 lbs based on 20 MPH max speed. Verify size of old rim before ordering. Replaces AL82488, A38404, C7NN1007J, D2NN1007N, D2NN1007S, D8NN1007BA, E1ADDN1015B, E1ADKN1015A, E6NN1007BA, G57046, K914312, K921475, K947941, VPH6001, 1660769M1, 1678319M91, 1678319M92, 1691618M92, 1691618R92, 1883333M92, 3114166R91, 509893M1, 509893M91, 57512110, 70000-00028, 751734R91, 82005056, 83900159, 83954658, 83960327, 9A306 (Item #: 116854, Ref: FW55166) $78.00

Tire Inner Tube - This Inner Tube fits 4.00 x 15, 5.00 x 15, 5.90 x 15, 4.50 x 16 and 5.00 x 16 tires. It has a TR-15 valve stem. Valve height 1.38 inch, diameter 0.65 inch. (Item #: 118299, Ref: 500X15TB) $17.15

Tire Tube - For 5.50 inch, 6.00 inch, or 6.50 inch X 16 inch tires. This is a bias style tube, not for radial tires. Not for recreational use. (Item #: 118295, Ref: WHS050) $19.10

No
Picture
Tire Tube 28 Inch - This 28 inch tire tube is used for all tractors with the following tires: 10.00 inch x 28 inch, 11.00 inch x 28 inch, 11.2 inch x 28 inch and 12.4 inch x 28 inch. (Item #: 158249, Ref: WHS058) $64.00

No
Picture
Tire Tube 32 Inch - This 32 inch tire tube is used for all tractors with the following tires: 7.00 inch x 32 inch, 8.00 inch x 32 inch, 9.00 inch x 32 inch and 9.5 inch x 32 inch. (Item #: 184736, Ref: WHS062) $67.00

No
Picture
Tire Tube 38 Inch - This 38 inch tire tube is used for all tractors with the following tires: 10.00 inch x 38 inch, 11.00 inch x 38 inch, 11.2 inch x 38 inch and 12.4 inch x 38 inch. (Item #: 183819, Ref: WHS064) $82.00

Wheel Clamp - Wheel clamp holding disc to rim for double ramp type on power adjustable rims. For 28 inch rim on tractors 2000, 3000, 4140, (10-1968 to 1975); 2600, 3600, 4100, 4600SU except Baseldon models, (1981 to 3-1990); 3230, 3430, 3930, 4130, 4630, 4830LCG, (3-1990 to -) Use with rims PAR10X18 and C5NN1050J and C5NN1050H. Also replaces 3615259M1, 70235676 and 7000000241, E5NN1043AA. (Item #: 124526, Ref: 898021M1) $18.20

Wheel Front 8X16 - Front Wheel 8 inch x 16 inch ; 6 bolt, 6 inch circle, 4.62 inch pilot. (Item #: 180445, Ref: D5NN1007A) $112.00