TJ, I hope this helps. Autobody Master has been around for several years and is a top quality product. It is compatible with all other major brands. I have used this product for many years without any problems, the price is very reasonable, compared to the major brands, like Dupont, ppg etc. As for primer color, being you are going to paint solid base colors, like a solid red or gray it wouldn't make much of a difference because your going to be shorting a complete project. Now if the colors were of a transparent base then primer color could and will make a difference in the final color outcome. This is a product I buy at O'Rellys Auto Parts stores in MO.
Epoxy Primer An outstanding quality, two component, isocyanate, lead, and chromate free epoxy primer or sealer with good corrosion resistance. The primer offers excellent adhesion to prepared metal, fiberglass and aluminum surfaces. Part # Description Size 8411 Epoxy Primer Green/Gray Gallon 8412 Epoxy Primer Green/Gray Quart 8413 Epoxy Primer Black Gallon 8414 Epoxy Primer Black Quart 8415 Epoxy Primer White Gallon 8416 Epoxy Primer White Quart 8121 Epoxy Catalyst Quart 8122 Epoxy Catalyst Half Pint Substrates • Fully Cured Finishes - Sand with 240-320 grit paper • Steel, Galvanized& Aluminum - Sand with 80-180 grit paper • Fiberglass and SMC - Sand with 150-240 grit paper • Always clean surface prior to application with 5900 or 5910 wax & grease remover. Mixing VOC Compliant Primer Conventional Primer Conventional Sealer 4 parts Epoxy Primer 4 Primer 4 Primer 1 part Epoxy Catalyst 1 Catalyst 1 Catalyst Up to 1/2 Part Urethane Reducer 3 Urethane Reducer 4 Urethane Reducer 5 Min. Mechanical Induction 5 Min. Mechanical Induction 5 Min. Mechanical Induction Set Up Tech Info Tip/Needle: 1.5mm to 1.8mm Spot Air Pressure 35 - 45 psi / HVLP 5 to 10 psi at cap Overall Air Pressure: 45 - 55 psi / HVLP 5 to 10 psi at cap VOC Primer Conv. Primer Conv. Sealer Viscosity (#2 Zahn) 20-25 Sec 19-22 Sec 16-18 Sec Film Build 1.0-1.2 mils DTF .8-1.0 mils DTF .5 mils DTF Coverage (@ 1mil) 481 Sq. Ft. 336 Sq. Ft. 288 Sq. Ft. Application VOC Compliant Primer Conventional Primer Conventional Sealer 1 full wet coat 1-2 full wet coats 1 wet coat w/10-15 min. flash Drying VOC Primer Conv. Primer Conv. Sealer Sand Time Not recommended 60 minutes Not recommended Recoat 60 minutes 60 minutes 30 minutes Topcoat 60 minutes 60 minutes 30 minutes Pot Life 8 hours 8 hours 8 hours Physical Data Volume Solids RTS 30% 21% 18% VOC RTS 4.8 lb/gal. 5.5 lb/gal. 5.7 lb/gal. Humidity Resistance Excellent Excellent Excellent Salt Spray Resistance Excellent Excellent Excellent Master Tips Do not use over lacquer products. Recoat within 72 hours. Greater than 72 hours, scuff sand before top coat. In temperatures over 77°F recoat within 36 hours.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Magic Moments - by Tyler J. Woods. Magic moments don’t just happen. You have to help them along. This morning, I got up early. It is my day off from my regular workweek and I had a lot of things to do. It’s fall, and with winter coming on, there is a lot of work to do before weather closes in.
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
