Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Implement Alley Discussion Board

Re: IHC plows


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Hugh MacKay on March 14, 2006 at 18:32:24 from (216.208.58.148):

In Reply to: Re: IHC plows posted by FromJB2 on March 14, 2006 at 16:56:31:

JB2: Actually it was a bit further east than ON. You are however very correct, the Ace would lay a beautiful furrow even as slow as 1.5 mph. You just loaded the tractor with enough bottoms to load it at 3 mph. I my opinion there is still nothing to match an ace bottom in stony soil. What we had was the ocasional stone, and they were large enough to be murder on plows. The trip hitch was fine for 2 bottoms, but once you increased the spring tension on the hitch, to pull 3-4 bottoms, you lost some of that protection.

I went from my old IH trailer plows to a new 510 semi-mount 5x16 with super chief bottoms. Pulled that a few times with 1066, but could clearly see hired help would soon make mincemeat of that plow, in those ocasional stones. Yes, it had trip beams, and they tripped but that did not eliminate breakage. I fixed those young lads, put the 5x16 plow behind the 656 and said, "Now boys that will cure the fast plowmen." Plowed for years with that setup, neighbor up the road was pulling 5x16 trailer with a Cockshutt 570 diesel.

High speed bottoms are little more than an expensive way to plow. If you fully load the tractor with bottoms at 3 mph, the cost of wear parts per acre will be 50% less than a tractor pulling less bottoms at 5mph.

The 60 hp tractor at 3mph pulling 5x16 plow also actually plows as much ground per hour as the same tractor at 4mph pulling 4x14 bottoms. If you get into better going and increase each by 1 mph, they will still plow about the same acres per hour.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Madison's County - by Anthony West. Philip Madison has been a good friend of mine for quite some time. He has patiently suffered my incessant chit chat on the subject of tractors for longer than I care to remember, and on many occasions he has put himself out, dropped what ever it was he was doing, to come and lend a hand cranking handles, or loading a find onto a trailer. Although he himself has never actually owned or restored a tractor, he was always enthusiastic and always around helping with other peoples projects. ... [Read Article]

Latest Ad: Super WD9. [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy