Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Safety wire bolts


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Aaron Ford on March 01, 2007 at 17:28:54 from (72.84.41.85):

In Reply to: Safety wire bolts posted by 37 chief on February 28, 2007 at 19:16:39:

4 years of installing and removing the Gau-8A anti-tank gun in A-10s made me a pro at this stuff.

You will need one pair of safety wire pliers. Harbor Freight sells them cheap. The 9 inchers will do fine. Also get a roll of .032 stainless wire. You will have about 20 bucks in this.


My engine bolts were single drilled so I installed the safety wire in a D-pattern. I figure yours are the same. Make a U with 18 inches of wire. Run one leg through the hole and the other around the bolt and stretch both wires toward the attachment point. Make the D so that any tension on the wire will serve to tighten the bolt. Cross the wires at the point where they pass the second attachment point or the next bolt. Atach pliers to the wires where crossed and pull on the knob. Do this several times til you get 8-10 twists per inch and either tie off to the attachment point or make your D on the next bolt. When finished, trim the excess and use your needle nose to bend the sharp ends down to avoid a potential snag. Should look pretty trick when you are done. Even pros screw up and make the D backward or twist too much wire. Lotsa practice helps.

After you get it all down, try doing it above your head as far as you can reach, in the dark, 16 inches deep inside a space about the size of a milk jug. A squished milk jug.

Then try no to punch the QA guy when he wants you to cut it out to prove that you had exactly 8-10 twists per inch.

HTH

Aaron


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy