Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Massey 1135


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Raleigh boulware on January 24, 2007 at 08:17:09 from (192.133.192.1):

In Reply to: Re: Massey 1135 posted by gemsvc on January 24, 2007 at 07:02:37:

The transmision and the reare end are the two area that have always scared me the most on these things! The engine well worse coem to wores i can always do an In Frame my self. IF I DID NOT PAY TOO MUCH TO BEGIN WITH!! But transmision work can be litterally catostrophic! I never knew of a good way to test the transmision except for this going down hill deal. I guess I will make more of an effort to try the next one down hill.

Blow by in the engine is not that big a deal, thats if the tractor is priced right. The problem I have is paying $7500.00, $8,000.00, $9,000.00 and then been told "Oh the engine is fine it just has a little blow by"....Well then if you don't want to dyno and you know it has about half the life left, cut your price $4000.00 to $5000.00 rang and I will consider it. that way I can invest $3500.00 in an over hual by either my self or a good engine shop.

My over all thing is about price, money, investment, and getting your money back when it is time to sale. This is my main reason for avoiding a new JD 6603. I had a JD dealer told me hey, "That 4020 you buy it for 8K today you might in 5 years might be able to get 9k for it or at least your money back. I can't say the same for a new machine."
It just does not make sense to me not do it. It cost almost nothing to do. You have that nice big PTO shaft to connect to, take advantage of it. I tell my self if only used cars had a PTO to connect to think of how many lemons we could avoid.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy