Tractor Talk Discussion Board |
Re: Deutz D4006 misc. info requested
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Norberg on September 03, 2006 at 18:44:13 from (64.91.59.89):
In Reply to: Deutz D4006 misc. info requested posted by Joe Leonard on May 21, 2006 at 11:39:15:
Does it hiccup under a heavy load with the tractor idling? If so, chances are it is a bad o-ring in the "brain" of the 3-point unit. Before you start, you'll need to drain some of the hydraulic-oil as well as remove the cover under the seat on top of the 3-point unit. If your tractor has a remote hydraulic valve, you will need to remove it. If it just has the power-beyond block-off plate in place of the remote-valve, you'll need to remove it. Behind the plate/valve, is an allen-head screw. Also, on the front right corner of the 3-point unit is a circular looking piece with a regular bolt and an allen head screw in it as well. Remove both of these allen head screws and grab ahold of the "bolt" head with a pair of vise-grips. with a bar, pry between the "bolt" and the allen head screw so that you rotate the "brain" clock-wise. MAKE SURE YOU HAVE REMOVED THE ALLEN HEAD SCREW BEHIND THE POWER-BEYOND BLOCK-OFF PLATE/VALVE BEFORE YOU PRY!!! pull on the vise-grips after rotating the "brain". You may need to pull very hard (tap vise-grips) with a hammer. Once removed, there will be an o-ring that lays in a recess on the side of the "brain". Look to see if there is any damage to the o-ring. Sometimes, the o-ring may not look damaged, but simply replacing it fixes the problem most of the time. Put everything back together in reverse order of disassembly with the exception of needing to rotate the "brain", most times as long as you lube it with hyd. oil you don't need to rotate. Just make sure not to pinch the o-ring or let it slip out.
Replies:
Home
| Forums
Today's Featured Article -
What Oil Should I Use? - by Francis Robinson. I keep seein this question pop up over and over again in discussion groups all over the web. As with many things there are often several right answers and a few wrong ones. Some purist I'm sure will disagree to no end with what I will tell you but most of us out here in the real world don't really care do we ? Some of them only bring their noses down out of the air long enough to look down them anyway. If you are like me you are only doing this old tractor stuff because you enjoy it. You
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|