Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Seeking Trailer Building Advice


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by KEH on July 24, 2006 at 12:09:01 from (209.213.23.31):

In Reply to: Re: Seeking Trailer Building Advice posted by Buzzman72 on July 24, 2006 at 08:54:18:

I have built some trailers and hauled square bales in my younger days before I got a round baler. Some observations:

You did not say what size tires you will be using. If you are using the 8.00 x 14.5 lowboy tires they will carry the hay you are likely to put on it.
When I was hauling square bales, I wanted the trailer to be as close to the ground as possible. If you build an 8 ft. wide bed above the wheels it will be higher to throw the bales up but if you have 2 people working it won't be as much of a problem and the extra capacity will make up for the inconvenience.
I think if you add a dovetail to the back it will take too much weight off the tongue making it pull badly. When hauling hay on rough ground a dovetail might drag the ground also. I have this problem on a gooseneck trailer. The axle spacing is ok for the trailer as is.
I don't think you gave the depth of the frame members, but they probably are plenty strong. If the strength worries you, weld a flat plate on one side of the rails the length of the trailer. 1/8 x 4 inches should be more than enough.
Was this a travel trailer or a mobile home? The width between the wheels sounds narrow for a mobile home. The last trailer I made had 6 1/2 feet between the wheels. That barely wide enough for a medium sized tractor. However, you have to go with what you have.
Don't forget lights and safety chains if you are going to run it on the road.
Hope this helps.

KEH



Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Restoration Story: 1951 Farmall H - by The Red (John Fritz). I have been a collector of Farmall tractors since 1990 when I first obtained part of the family farm in Eastern Indiana. My current collection includes a 1938 F20, 1945 H, 1946 H, and the recently purchased 1951 H. This article will focus on what I encountered and what I did to bring the 1951 NEAR DEATH Farmall H back to life. ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy