|
Tractor Talk Discussion Board |
How do I plow a hillside REVISED
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by CharlieT on April 13, 2006 at 07:42:01 from (157.225.178.190):
I have to plow a 15 acre field where the lower 2/3 is a slight hillside of 20 deg slope and the upper 1/3 is realtively flat. I have a JD 730 gas pulling a 3 bottom 14" hydraulic lift trailer plow. West <==1200'==> +++++++++++++++++++++++++Lower Right Corner +++++++++++++++++++++++++slope +++++++++++++++++++++++++slope +++++++++++++++++++++++++slope +++++++++++++++++++++++++slope +++++++++++++++++++++++++slope +++++++++++++++++++++++++slope +++++++++++++++++++++++++slope +++++++++++++++++++++++++ Slope Starts Here +++++++++++++++++++++++++ flat +++++++++++++++++++++++++flat +++++++++++++++++++++++++flat +++++++++++++++++++++++++flat +++++++++++++++++++++++++flat +++++++++++++++++++++++++flat +++++++++++++++++++++++++ Upper Right Corner East In the past when I had to plow smaller sections, 2 or 3 acres on the slope, I would start on the lower right hand side and plow always right to left so that the sod would always turn towards the downslope side of the hill. When I got to the end of the row, I would lift the plows and return to the right hand side of the field before I would start plowing again.
I learned from experience that if I plowed from left to right on the return, with the sod turning towards the up slope side of the hill, always about half of the sod would fall back into the furrow. This method is not bad when I had only a few acres to do, but I can not see myself doing this for all 15 acres. With the price of gas here in NY at $3 , I would waste a hell of a lot of fuel with this method. Can someone suggest a different method of plowing keeping in mind the sod problem on the slope part of the field.
Replies:
Home
| Forums
| Order Support
Today's Featured Article -
New Hitches For Your Old Tractor - by Chris Pratt. For this article, we are going to make the irrational and unlikely assumption that you purchased an older tractor that is in tip top shape and needs no immediate repairs other than an oil change and a good bath. To the newcomer planning to restore the machine, this means you have everything you need for the moment (something to sit in the shop and just look at for awhile while you read the books). To the newcomer that wants to get out and use the machine for field work, you may have already hit a major roadblock. That is the dreaded "proprietary hitch". With the exception of the
... [Read Article]
Latest Ad:
one 8n and one 9n tractor. totaly restored,pretty much everything is new. one 6ft blade good shape.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|