|
Tractor Talk Discussion Board |
Re: City boy in the country, needs help...LOL
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by txgrn on May 04, 2005 at 05:43:40 from (209.151.112.107):
In Reply to: Re: City boy in the country, needs help...LOL posted by thurlow on May 04, 2005 at 05:17:32:
Cool in my conversations means what Thrulow said, and has to be taken in context. If you say geez it's cool out here, you're talking about temp. If you say geez man that's a cool tractor, it means that you like it. On the mechanic, if I were asked to check out a piece of machinery for someone, I wouldn't drive it to a mud hole and get it stuck just so I could check out the hydraulics. So a problem of the magnitude mentioned could go unnoticed, even for a competent mechanic. In my opinion, lifting the front of the tractor off the ground and pulling it forward with the hydraulics is hard work for the system and I wouldn't worry about it.
What's probably happening is that your hyd fluid viscosity is thinning in the heat and you are loosing psi as a result. One way to tell, is to carefully feel a hyd lind fitting or some associated metal with fluid inside. If it's hot to the touch your fluid is breaking down. Whining I associate with vibration. Vibration can be caused by bubbles among other things. Bubbles can be formed when the air trapped in the oil is released like could happen in the situation described. Once the tractor is shut off and the fluid cools, the air goes back into solution....I'm talking about the air that encircles the molecules of the oil that you can't see unless you put the oil in a glass beaker and pull a vacuum on it. Like the reverse of that provess when you run your tractor for awhile and and pop the cover on your tranny and look down at the gears and lube and the lube looks milky (but it's only suspended air you just whipped into it). Good job city boy, just don't be too hard on your equipment. May not last. My 2c Mark
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Restoration Story: 1964 JD 2010 Dsl - Part 2 - by Jim Nielsen. Despite having to disassemble the majority of my John Deere 2010's diesel engine, I was still hopeful I could leave the engine-complete with crankshaft and camshaft-in the tractor. This would make the whole engine rebuild job much easier-and much less expensive! I soon found however, that the #4 conrod bearing had disintegrated, taking with it chunks of the crankshaft journal. As a resul
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|