|
Tractor Talk Discussion Board |
Re: use of engine additives to misrepresent...
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Indydirtfarmer on December 16, 2004 at 04:45:39 from (66.83.236.250):
In Reply to: use of engine additives to misrepresent... posted by Jonboy on December 15, 2004 at 12:12:16:
It's only natural to suspect the person you bought a tractor from when you find something like you described. Truth is, I've see several tractors that were bought and sold without the last seller doing a thing. The cover-up took place 2 or 3 owners ago. I try to buy, and only sell equipment that has been serviced BY ME before it leaves my yard. I have to pass on that cost, but I'm not selling someone a tractor that'll explode when they go to unload it.... Over the years, I've got burned a few times myself. When it happens, I just bite the bullit, and make whatever repairs are needed. Not the most profitable way sometimes, but at least I can sleep at night... I own a tractor right now that's a perfect example. It had a hole in a cylinder sleeve. (wet sleeve pitting) It was traded in at a John Deere dealer I do business with. They have been very honest and outgoing to me for years. I know they wouldn't have deliberately decieved me. The tractor had enough radiator stop-leak in it to clog up the leak unless the tractor got fully warmed up. Then it would start dumping collant into the oil pan. From all appearances, the oil was drained, then replaced with USED oil. so as not to look like it had been changed (and no OTHER service done) It took about 2 or 3 hours of working it for the trouble to rear its ugly head. 2-1/2 gallons of anti-freeze in the oil pan....
It took almost $3500 to fix it. (Crankshaft damaged. some damage to the block when main/thrust bearing spun. sleeves, pistons, boil out block, ect..... The dealer picked up the labor tab. It happens....As best we can tell, the (respected) Cardiologist that traded in the tractor did the "cover-up". I can't prove it, and he sure isn't going to admit to it... The high cost of doing business.....John
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Measuring with Calipers - by Staff. The legs of inside calipers are curved outward at the extremities to facilitate measuring small holes, while outside caliper legs have a large curve inward to increase their capacity for large work. Firm-joint calipers are adjusted approximately by the hands and then set to the feel of the work by tapping them on a metal surface. It is a common practice when opening calipers by this means to tap the top of the joint. It is better, if possible, to tap the inside of the legs, as repeated blo
... [Read Article]
Latest Ad:
Late 50s early 60s international harvester 560 with cultivator
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|