Tractor Talk Discussion Board |
Re: Cheapest way to erect a shed
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by kyhayman on September 05, 2004 at 07:15:11 from (68.233.199.66):
In Reply to: Cheapest way to erect a shed posted by Phil from Maryland on September 04, 2004 at 15:17:36:
I build about one a year attached to a barn. So far, here, we dont have to worry about any inspection or codes as long as it is built or subbbed out by the farm owner (except electric, if setting a new service). Got 20 and only had damage to one, it is a 3 sided shed, open to the east, 14.5' on the low side and 17' on the high side, 30' open span. Had 110 mile an hour straight line winds out of the east and I lost part of the roof and sheeting. Insurance was good, no problems with how it was built. Rafters (2x8's) held, stringer boards pulled out as the tin was screwed in and the stringers nailed with coated 10's. Shop we built in 1987. Put 14'x10" cedar poles 3' in the ground on 12' centers. Used 2 2x10's x 26' fir on each one (one on each side). Bolted a 2x6 plate on the side of the barn and set the other end of the rafters on it. Put 2x4 stringers 3' apart accross them. And also around the outside of the posts. Used tin on the outside, new tin on the roof. Lumber then cost me 40 cents a board foot for oak. Lined the inside with chip board. Surface mounted my electric and ran a feed off the barn. Poured the floor in one pour. It isnt pretty but it is functional, cost less than $2000 back then. On what I built this summer. Similar designs only did not use the long rafters, Put posts in 14' out and again at 28' so I could use 16' oak for the rafters. New metal (buy getting assorted colors and lengths my siding was $25 a square). 55 gallon barrel of black acrylic fence paint makes it all nice and uniform. Including ALL hired labor (but no floor) I spent right at $3000 each on 2-28x72x 15' lowside 18' high side sheds.
Follow Ups:
Home
| Forums
Today's Featured Article -
Sunday Drives - by Cowboy. Summer was finally upon us here in Northern Maine. We have two types of industry up here, one being "Forestry" (Wood Products) and the other "Farming" (Potatoes). There is no shortage of farm tractors and equipment around here! I have been restoring old Farm Tractors for the past 6 years, and have found it easier and less expensive to hit all the auctions and purchase whole tractors for parts needed. My wife who works at a local school, and only has weekends and summers off, while on t
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|