|
Tractor Talk Discussion Board |
Re: How Long Will A Tractor Last????
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Brokenwrench on March 22, 2004 at 13:04:39 from (205.188.208.103):
In Reply to: How Long Will A Tractor Last???? posted by ken theobald on March 22, 2004 at 08:50:17:
One of the most frequent questions on these boards concerns electrical problems on 50 year old tractors. Either they won't charge,won't crank,or won't start.These are on a tractor with the simplest of electrical systems,starter,generator,regulator,battery and lights.Multiply these problems 100 fold with the advent of computers,potentiometers,microswitches,multiple circuit boards,relays,20 pole pin connections and 14 miles of wiring,and current measured in fractions of a volt or amps.The new tractors themselves may be around as museum relics,but I seriously doubt if many will be running. The late 80's early 90's tractors are already starting to suffer from numerous electrical malfunctions. Inoperative lights and guages,shifting problems,3pts that raise and won't lower,or vice versa are all too common problems now on high hour tractors.Most common problem is corrosion and dirt in the supposedly sealed connectors. The repair is to replace harnesses and components damaged by corrosion or dirt,or voltage spikes. The average equipment owner doesn't want to hear that the repairs needed to make their 3pt lift is going to cost $8500 because "when you were welding on the drawbar the residual voltage backfed into the 3pt hitch module,shorting it out, and then you tried to run a jumper wire to make the hitch work that shorted out the main computer,and we have to take the cab off to get to it"
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Product Review: JB Weld - by Staff. JB Weld is basically an epoxy glue that does an exceptionally good job of bonding to cast iron and steel along with several other materials. As I mentioned, it is so common that I have yet to buy a tractor that did not have JB Weld used somewhere. It is sometimes used so well you can't tell its there and other times used as a sloppy quick fix. Finding where and how it can be used correctly is key to whether you are using it as an "inelegant hack" or an integral solution to difficult and expens
... [Read Article]
Latest Ad:
WANTED Front grille/nose assembly for Massey Ferguson 1160 (also fits 1180 & 1190). Headlight-mount section. AGCO Grille 3706022M91 (supersedes 3705942M91), cover 3705494M1/M2, holders 3705501M91/3711158M92. New/NOS/good used OK. Jonesboro, AR - will pay shipping. Photo appreciated. Thanks
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|