|
Tractor Talk Discussion Board |
Re: More Rotovator talk
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Robert in W. Mi on September 09, 2003 at 12:21:41 from (205.217.79.201):
In Reply to: More Rotovator talk posted by Indydirtfarmer on September 09, 2003 at 04:40:17:
When you rotavate all the time like i do, you just take it in stride. Last week i was rotavateing logging roads. I hit rocks as big or bigger than ever before. The rotavator junmped clean out of the ground several times!! I was at this place two partial days, and i broke 2 tines. No big deal, i brought home $477.00. One time i rotavated a place that should have been called "the rock farm" !! Every hill was sand, and when you'd get to the bottom of the hill it was pure clay!!! Then there was the rocks, and more rocks!! The guy felt bad as it was tough going all day!! When i was leaveing he and his buddy came over and said they had 10 acres of muck ground (peat beds) that they wanted rotavated. It was a ways away, and i said i really didn't want to drive that far. He said, he'd pay millage, and it was such "easy going" it would "make up for" all the rocks on his place. As i was loading, and they kept talking, i finally agreed to do go the following week. When i got there, it was just as they described, so i unloaded and got going. All went well for about 10 mins., then i hit a big rock!! Next it was a huge picture window, the glass flew all over out behind!! A little further and i hit a 1-1/2" galv. 5' piece of pipe that locked the tines up!! I bitc*ed about that as i pulled it out, and got going again!! After about 100' i hit another that locked it again!!! Before the day was over i found 5 pieces of pipe, and a huge piece of foundation!! There was a fair amount of rocks, and even some stumps!! Finally i got down to the last 2 or 3 rounds and a huge electrical storm came, and i just barely got off the field because of the down pouring rain!! I ended up haveing to replace the drive line slip clutch plates after that job, but i don't remember breaking any tines??? Like i said, you just have to take them all in stride!! Robert
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Tractor Profile: Oliver 70 Row Crop - by Staff. The Oliver 70 was part of the "Fleetline Series" and was manufacturered from 1937 to 1948. The row-crop configuration could have either dual or single front wheels. The Oliver 70 was also offered in the standard, orchard and industrial configurations. The tractors were sold in Canada. An early advertisement states "Power when you want it - power when you need it - power to help put in crops when field conditions are right and time and help are limited. That's the power you'll find in an Oliv
... [Read Article]
Latest Ad:
Late 50s early 60s international harvester 560 with cultivator
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|