Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Ford tractor question???????


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Rod F. on August 28, 2003 at 20:55:44 from (142.177.87.154):

In Reply to: Ford tractor question??????? posted by Indydirtfarmer on August 28, 2003 at 09:10:59:

First step it to change the air filters. Mabey clean the outer filter, but replace the secondary. I wonder about the injectors. It got worse after the new injectors and valve job? If he just changed the nozzles, and not the whole injector, they would have to be set up properly on a pop tester. Even if he changef the whole injector, they still need to be checked. I assume the compression was good after the valve job? As for pump timing, it is primairly set on the gears, but there is a final adjustment on the pump mounting. There is a scribe mark on the pump ear that match marks on the backing plate. I think the zero on the plate has to match the mark on the pump. That is assuming that the pump is not internally timed. From what I understand, if they are internally timed, these scribe marks are not relevant for the purpose of setting timing. The timing was set at the factory. To remove an internally timed pump, the the doer should put a munch mark on the plate, so that he knows where it goes when it is time to put it back on. In this case, he probably didn't do that when he changed the timing. Try to set it back to the paint marks. That said, if there is nothing to go on, I would try setting it to zero, see how it works, and perhaps advance a bit from there. 1 index mark, I believe is 4 degrees. Standing behind, looking forward, turning the pump clockwise will advance the timing. As far as the smoke goes, they smoke some anyway, under load. IT is also possible that somebody screwed with the delivery when it was new, and then it is going to smoke. IT will pull pretty good too. Well, that's a few confused thoughts for tonight.

Rod


Follow Ups:




Post A Followup

:
:

: Re: Re: Ford tractor question???????

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - History of the Nuffield Tractor - by Anthony West. The Nuffield tractor story started in early 1945. The British government still reeling from the effects of the war on the economy, approached the Nuffield organization to see if they would design and build an "ALL NEW" British built wheeled tractor, suitable for both British and world farming. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy