|
Tractor Talk Discussion Board |
Re: setting up a garden
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Bill Smith on September 02, 2002 at 09:39:39 from (128.242.4.59):
In Reply to: setting up a garden posted by mark b on August 28, 2002 at 22:25:51:
Just a couple words of advice. If you have a good spring or pond, build your garden down below it. Makes it real cheap and handy for irragating. Also, if you don't have real good soil, I would advise you to do some soil building, such as plowing some manuer into the soil. You may want to have a soil test done to see specifically what it needs. I would also advise you to plant a small portion of perminate garden ( especially if the irragation situation is there) like fuit trees, asparagus, horse radish, strawberry's, ext. Sounds to me like you are on the right track if you pick up those peices of equipment. Just remember that if you pick up something that you end up not using you can always get rid of it. Just put it up for sell. If I was you I would get a newer, pretty good sickle mower to mow hay with. The newer ones are much better than the older ones is my opinion. You will also need a hay rake. One that works and don't break down will be just fine. The newer style with the front wheel on it is going to cost you more money than the older styles. If you do like I do, (I hire my bailing done) you will need something to move big round bails with. I got a MF235 and like your tractor it is to small to haul those bails with. So I do like mentioned in one of the other posts, I use a bail cart. Mine is probably about the best cart you can get. It is real heavy duty, and it has a hydraulic cylinder instead of a cable, or a break actuating deal. The bottom of it is half moon like and folds down over the axle backwards. Has a couple of arms that grab the sides when raising up, and brings the center of bail up and over the axle which gives you some tongue weight while traveling. Good luck to ya.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Fabricating Sidesheets - by Chris Pratt. The easiest and best first-time project for wanna-be sheet-metal workers like myself is flat or nearly flat metal cut and drilled to be a tractor's sidesheet. A sidesheet is sheetmetal to cover either the engine as in the case of early Oliver's, Massey-Harris' and many crawlers or the wiring and electrical components as in the case of the Massey-Harris Pony, Allis Chalmers' D Series (D-14, D-15, D-12, D-10, D-17, and D-19). The need for fabricating becomes obvious when you go to buy any of these
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|