|
Tractor Talk Discussion Board |
Re: diesel timing, intake through the exhaust
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Trucker on July 14, 2002 at 17:48:31 from (65.167.169.14):
In Reply to: diesel timing, intake through the exhaust posted by Kevin O'Brien on July 14, 2002 at 12:41:50:
I'm fairly sure you are 180 degrees out.With the piston on number 1 cylinder all the way up,check your marks,if you dont see them,turn the engine untill you do see them.if you turn the crank one complete revolution,then see the marks, you are out 180 degrees.The cam turns at half the speed of the crank,so for every 2 crank revolutions,the cam turns one time.If you had the crank on the exhaust stroke and the cam on the fire stroke it might make it suck through the exhaust,and exhaust on the intake.I hope this isnt confusing you worse,but if you think about it,when the piston is coming up,and the intake has just closed,it has to be right,marks or not.I would take the cam gear off,or idler or whatever to reset the timing,carefully turn the crank one revolution,mark where it is now on the harmonic balancer and front cover,turn it one revolution,you might have to turn the cam a little to get it to turn all the way around in case the piston hits the valves,then when i got the crank turnd back to my mark,hook the cam back up by the marks if possible.I think that will fix it,just dont turn the cam any more than you have to to get the crank to go all the way around,mark its position as well,and maybe you wont even have to turn the cam anyway,but if you do,put it back in the same place it was,and when you get the crank back to where it was hook it back up.Also you want to turn it in the direction of rotation of the engine.Another thing to do might be(now this is just an idea)but if its a 4 cylinder for instance,if you can take the number 1 fuel line off and the number 4 fuel line off,and hook the number 1 fuel line to number 4 cylinder,that one might fire.It might fire,might not,maybe it would not be a good idea to do that.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|