Posted by da.bees on May 25, 2021 at 20:10:00 from (147.160.222.152):
In Reply to: wife---rotator cuff posted by Ellis Kinney on May 25, 2021 at 06:22:53:
I'm at 12 weeks after surgery and prospects are not looking to suit me. Hard fall on shoulder almost 12 months ago. Suffered with it 3 months not knowing what was wrong. Went to Dr who did exrays and mri and said partial tear in rc. Suggested cordazone shots,no mention of surgery, therapy or taking it easy or resting shoulder. I asked if that is a cure and he said no,just temporarly relieve's pain. Put up with it another 6 months then went to different Dr who said I should have done therapy 6 months earlier and I had finished wrecking my shoulder by continueing to lift,push and pull. Suggested surgery which I had done. They handed me a rope with pulley and said come back in 2 weeks. At 2 week follow up he told me I needed to pull arm as high as possible with pulley. I told him it already felt like something was tearing and he assured me I couldn't injure myself on the pulley. Went home that afternoon,gritted teeth and pulled hard on rope. Pulley strap had been wedged for 2 weeks in top of closet door per instruction sheet in bag with pulley. When I put arm under extra tension the *%!$#@ strap sliped and it hurt like never before. Next morning I picked up a pulley at Lowe's with a heavy duty support bracket and found I wasn't able to pull arm as high as I could 24 hours earlier. It has been 10 weeks since that happened,not much improvement,pain worse than first 2 weeks and Dr want's to perform another procedure with projected recovery taking 12 more months. I'd like to hold a couple of doctor's heads under water over their lackadaisical ways. Haven't decided what I should do but haven't ruled out making the last dr and pulley mfgr pay for everything going foward with a different orthapedic team. I may get my granddaughter to post pictures of pulleys from dr's office and from the home improvment store. I think you would agree with my opinion of their reliability when so much is at stake. My best wishes to you and your wife Ellis.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Museum Coverage: The Stuttgart Agricultural Museum - by Cindy Ladage. While cold wind was blowing back in Illinois, in Arkansas, daffodils were in bloom, and the Magnolia trees were adorned with fragrant blossoms. Stuttgart, Arkansas was the site of this year's winter Minneapolis Moline Collector's show February 25-27, 1999. The show was held at the Oliver Museum created by Don Oliver, the pioneer of the four wheel drive tractor. Oliver along with Gale Stroh and Kenneth Bull using Minneapolis Moline tractors and parts created what has become known as
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
