Posted by UP Oliver on August 17, 2019 at 07:04:47 from (68.70.134.89):
In Reply to: Re: JD #30 Bale Kicker posted by Roger in Iowa on August 16, 2019 at 19:28:59:
Thanks for the reply Roger.
The pan will come back but only after I shut off the PTO. Then it slowly falls back into position. Sometimes I have to give a little shove so it will latch.
You obviously know a heck of a lot more about this than I do, so I'll describe the initial break down as best I can. I was baling and broke a shear bolt on the flywheel. I shut off the kicker to straighten things out back there, and then got back on the tractor and turned on the PTO and went a few feet and realized I forgot to put the kicker back on. When I put the kicker on it kicked even though there was no bale there, and went right back to the latched position. It did this several times until I finally got back over to the tractor and shut off the PTO. I don't know if it latched each time or not when it was repeatedly going through the kicking motion.
I tried it one more time out there in the field and when I put the PTO on the pan just shot out like it was kicking a bale but there was nothing on the pan. And the pan stayed out, extended. I shut off the PTO and went back and shut off the kicker. I put them all on the ground the rest of the day. I got the baler in the pole barn and adjusted as best I could. As of right now I can put the PTO on and the pan stays in the latched position, and then when I use the trip lever it extends out like it's throwing a bale but it stays extended. So that's where I'm at.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Fabricating Sidesheets - by Chris Pratt. The easiest and best first-time project for wanna-be sheet-metal workers like myself is flat or nearly flat metal cut and drilled to be a tractor's sidesheet. A sidesheet is sheetmetal to cover either the engine as in the case of early Oliver's, Massey-Harris' and many crawlers or the wiring and electrical components as in the case of the Massey-Harris Pony, Allis Chalmers' D Series (D-14, D-15, D-12, D-10, D-17, and D-19). The need for fabricating becomes obvious when you go to buy any of these
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
