Need to know a few things... Where are you? What kind of grasses? Your best estimate of percentage of field that has a sufficient stand of grass now? It may not be necessary that you need to totally kill and start over with entire new seeding. I have seen some bad looking, neglected fields of grass brought back with weed control , proper fertilizing and over-seeding (broadcast seeded before a rainy spell or no-till drill) in August with grass and clovers.
I would do the following: First get a soil test done. Apply all needed limestone as soon as soil can support equipment this spring. Apply half the recommended plant nutrients as a dry fertilizer containing N-P-K, broadcast with a 3-point mounted whirly type spreader, at grass green-up. Apply the other half after first cutting.
Depending upon what weeds you are seeing dictates what I would do about spraying. If you have a scattering of Curly and Broad-Leaf Dock, walk your fields with a back-pack sprayer applying Glyphosate, with a little 2-4-D in the mix, to the Dock weeds when they begin to leaf out. After first cutting and grasses begin regrowth, if you have tough perennial weeds, use dicamba and 2-4-D or some other products designed for grasslands and pastures. (Be advised though that there are products that remain in the hay and after being eaten by animals is in the manure and will kill legumes and vegetables if manure is dropped in pastures or spread in fields or gardens.) After second cutting and some regrowth, identify weed species surviving and evaluate grass stand as to whether you need to do a total kill and get ready for a re-seeding later. If sufficient grass stand remains , apply 150- 200lbs./acre of 34% Nitrogen fertilizer mid-to-late August to boost growth for late September to mid-October cutting of fine leafy grass blades.
Use of liquid fertilizer in a sprayer requires use of a pump and tips in the nozzles that are resistant to fertilizer corrosion.
I have never sprayed 2-4-D in a fertilizer solution but a friend did. He found that he had to mix the amount of 2-4-D needed in water before adding it to the liquid nitrogen solution he was applying. Full strength 2-4-D did not mix well in the nitrogen.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Fordson F Ignition System - by Anthony West. A fellow restorer contacted me earlier this year asking for some help and advice on a model F that he was restoring. He had over a period of months spent a fair amount of his hard earned cash on replacement parts for the old "trembler" ignition. Sadly though all his efforts seemed to be a waste of time and money as he still couldn''t get the temperamental old thing to run correctly!! If i said that this was a little frustrating for him that would be "conservative" in fact the problem had reduce
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
