Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Heat pumps


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by W_B on March 28, 2014 at 05:01:45 from (155.188.183.18):

In Reply to: Heat pumps posted by Tx Jim on March 27, 2014 at 15:48:47:


George Marsh said: (quoted from post at 06:18:03 03/28/14)

Why are you the only one on YT sees that a heat pump doesn't work in all places?

Where I live, when you need them the most, sub zero temps, they don't work. If you try to use them they end up costing you more.



It's like anything else, you have to know how to use it properly. I can only relate my personal experience for what it's worth. We have an oil fired hot water heat system. Put in A/C unit and ducts when we bought the place (2900 sq. ft. story and a half). Lived with that arrangement for about 5 yrs. as heating oil prices continued to skyrocket. We took out a perfectly good unit (was able to sell it to get some $$ back) and replaced it with a heat pump. Now when it stays above about 30 we leave it in normal mode where the pump runs and if it can't keep up the oil burner kicks on... rarely does. When it turns colder we switch it over to "emergency" heat, that turns off the heat pump, but the inside fan runs, and the oil burner runs for heat. I can say since we made the switch our oil use has been cut dramatically. Unfortunately with heating oil now over $4 a gallon the bill is about the same, I shudder to think what we'd be paying if we didn't have the heat pump.

We had a ground source geo-thermal system in a house we built in 1992. That was the best, most efficient and cheapest heating/cooling system I've ever experienced and would have it again if we got to the point of building again. So, sir, with all respect, your friend who poo-poos geo-thermal is full of cr@p.

I recently got a "toy" that measures air temp and humidity. It's a professional tool that was in a box of tools I bought at an auction from a contractor that was selling out. I measured the air temp coming out of the ducts with just the heat pump running. It was about 85 at peak and 80 running over time. House air temp was at 68. Interestingly the humidity of that air was quite a bit less than the ambient air in the house. So yes, it feels "cold" but wasn't really, it's just cooler than your body temperature. Run long enough the house would heat up probably by ten degrees or more, just would take longer than the oil burner would heat it up.

This post was edited by W_B at 05:03:15 03/28/14.



Replies:




Add a Reply

:
:
: :

:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy