Posted by Jon Hagen on February 17, 2014 at 12:32:06 from (69.26.17.61):
In Reply to: Re: 6v to 12v posted by rrlund on February 17, 2014 at 11:23:54:
I do the same. I consider pos ground to be a dangerous oddball in an otherwise 99% 12V neg ground world.
Converting to neg ground eliminates some confusion when charging or jump starting. Also 12V neg ground allows you to use many modern polarity sensitive accessories that have permanent magnet motors or solid state electronics that are almost exclusivly 12V neg ground.
I am also not too keen on using a 6V generator to produce 12V using a 12V regulator. Not only does the 6V generator need more rpm to produce 12V, but the field impedience is wrong and causes more wear and problems with the already troublesome vibrating contact mechanical regulators.
My older tractors are all daily workers, not a parade queen in the bunch, so give me a reliable rotating field generator (alternator) with an accurate reliable solid state regulator built in.
Also, although I have just about given up thinking the public will ever understand,
There is no such thing as a coil with a built in resistor. You cant put a red hot resistor inside an oil filled coil can without having a burst and burn disaster. What some seem to think is a coil with a built in resistor, is actually a coil with a primary winding made from thinner, longer magnet wire that will run on 12V without an external resistor. No internal resistor is ever used, such a coil does not exist.
Your choices are a coil with a 1.5 ohm primary winding, that runs on 6V, or, when series wired with a 1.5 ohm external resistor, can run on 12V. The other option is to use a coil with a 3 ohm primary winding, which does not have any sort of resistor inside, which will run on 12V without the aid of an external resistor.
This post was edited by Jon Hagen at 12:59:06 02/17/14.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Women and Tractors - Tractor Engine Repair - by Teri Burkholder. One of the great things about working on a tractor engine with your other half is that you know what he is thinking of at all times and can anticipate his every move and his next thought of what he will do. With Ben, anyway, I can tell! He'll be busy working and I�m handing him tools and he says, "give me that..." and I�ve already got it in his hand or "hand me that....."and I�ve got the portable light right where he needed it placed to see. "Run in the house and get me a...."as I open th
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
