Posted by John in la on February 10, 2013 at 15:05:37 from (184.38.236.37):
On 2/8 MF Poor said; If it has gas in it, you aren't allowed to haul a plastic container of gas in a commercial vehicle. And you said; Could you please provide the statute on that from the FMCSR? My thoughts are...........
As I have told you in the past DOT has some very strict guidelines on Gasoline. Metal cans is not one of them to my knowledge but there are some guidelines that just went into effect or are about to that I have heard about but do not keep up with it because it does not envolve me.
The rules I know of allow Plastic jerrican: 3H1 or 3H2 per §173.201 and §173.202 3 – Jerrican H - Plastic 1 – Non removeable head 2 – Removeable head
Where it gets complicated is OSHA rules intertwine but even they have released a statement saying while it is a voliation tickets would not be issued. So as far as I know plastic cans are allowed. They must have the words Gas or Gasoline on them and they must be red.
Where it gets REAL complicated is when gas is mixed with ethanol. Pure Gasoline is a Class 3 Packing Group II material. Gasoline mixed with alcohol is a Class 3 Packing Group I material per §172.101 HAZARDOUS MATERIALS TABLE
So under §173.6 Materials of trade exceptions the general public and people that use Hazardous Materials in their line of work are allowed some exemptions from the hauling rules like paper work and such. If we look at §173.6(a)(1)(ii) 30 kg (66 pounds) or 30 L (8 gallons) for a Packing Group II, Packing Group III, or ORM-D material;
But once we mix gasoline with alcohol the rules change. §173.6(a)(1)(i) 0.5 kg (1 pound) or 0.5 L (1 pint) for a Packing Group I material;
So as you can see they allow pure gasoline to be hauled in containers up to 8 gallons because it is a packing group II material but gasoline mixed with alcohol can only be hauled in containers of 1 pint and still fall under the exemption.
So to answer your question. Plastic 5 gallon cans are allowed but you can not fill they with E10 gasoline and haul them home without proper shipping papers. I wonder how many follow that rule.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
