|
Antique Tractor Paint and Bodywork |
Re: Question about Orange Peel
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by CNKS on July 27, 2005 at 17:20:33 from (204.249.178.138):
In Reply to: Re: Question about Orange Peel posted by Rod (NH) on July 27, 2005 at 16:47:30:
I think my gun is set up right, and I always do the cardboard thing, mainly to make sure one side of the air cap is not plugged. I haven't used the 1.3 much, certainly not on the last hood I did. I think the pattern is a little smaller, I need to compare when I start painting again. I have not heard about the 70% overlap, the person I corresponded with knows his stuff, and would have told me. Regardless of tip size, he recommends INCREASING the pressure 5 psi for better atomization, leaving the fluid alone, it is maxed out anyway--I have done that, but don't notice any difference. But, I may do what you say and decrease the air pressure, need to practice some first. As I say, on flat surfaces I don't have any problem. As to increasing it, the implication is that the 10 psi tip pressure is because of enviornmental regs, increasing the gun pressure slightly results in better atomization, if that (enviornmental) is not a concern. But, you are then beginning to defeat the purpose (less wasted paint) of HVLP. I have thought about starting in the middle of the hood, as you say, but I thought that might not be wise because you are not immediately doing the overlap on the other half of the 1st pass. In other words, I thought it would be too dry, but it doesn't take long to do a small hood. However, then I get two chances for the overspray, one on each side of the hood. The 460 hood I'm going to do next is long, I think it exceeds 4 feet. That one is going to be interesting. I'll keep your suggestions in mind --Thanks.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Timing Your Magneto Ignition Tractor - by Chris Pratt. If you have done major engine work or restored your tractor, chances are you removed the magneto and spark plug wires and eventually reached the point where you had to put it all back together and make it run. On our first cosmetic restoration, not having a manual, we carefully marked the wires, taped the magneto in the position it came off, and were careful not to turn the engine over while we had these components off. We thought we could get by with this since the engine ran perfectly and would not need any internal work. After the cleanup and painting was done, we began reassembly and finally came to t
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|