|
John Deere Tractors Discussion Board |
Re: Power Steering on a 70
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Clooney on May 24, 2004 at 18:18:54 from (172.141.212.177):
In Reply to: Power Steering on a 70 posted by Buddy on May 24, 2004 at 14:11:55:
Buddy, you ask.. Quote: "My power steering works great turning to the right and back from right to center but not to the left from center. Is there an adjustment?">>> _Well, yes & no.. There are some adjustments that could help but your basic problem is probably a worn helix screw tip, or worn helix pin, or worn sleeve pin that goes in the cam slot.. ~You can try removing the helix screw & re-grinding the point on that, then setting the actuating sleeve end play [fore/aft play] to .002�.. [set the worm bearing end play first].. ~Seeing as you have a one direction problem you could also have loose worm bearings as that will effect the actuating sleeve end play also. ~Sometimes just setting the flow control pressure up a little will make the problem better [it isn�t a real repair but increased operating pressure can cover up a worn pin problem as it will turn out before the pin can hang in the sleeve slot.. ~My guess is you have a combination of problems that add up to your lack of assist in one direction.. Probably excess worm bearing end play, worn helix set screw tip [& probably a worn helix slot in the sleeve], worn actuating sleeve slots & pins, & possibly some steering vane leakage.. ~It sure wouldn�t hurt to do a steering vane leakage test before anything else.. ~I would have to type a novel to talk you through all the above repairs & checks & even then you would probably need pictures for some of the adjustments.. ~I am going to suggest you buy at the very least an I&T shop manual [JD-10] as it will do a fair job of walking you through the above checks & settings.. Better yet would be the Deere steering service manual SM 2050 [more money though].. I will be happy to answer any of your questions on your steering but a how-to on checking, setting & adjusting that steering would get real long winded.. [email protected]
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Field Modifications (Sins of the Farmer) - by Staff. Picture a new Chevrolet driving down the street without it's grill, right fender and trunk lid. Imagine a crude hole made in the hood to accommodate a new taller air cleaner, the fender wells cut away to make way for larger tires, and half of a sliding glass door used to replace the windshield. Top that off with an old set of '36 Ford headlight shells bolted to the hood. Pretty unlikely for a car... but for a tractor, this is pretty normal. It seems that more often than not they a
... [Read Article]
Latest Ad:
Ford 3-Point Single Bottom Moldboard Plow with Coulter
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|