Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: IH 2000 Loader-Need Advice


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by KDJ in IA on December 09, 2006 at 16:31:32 from (69.66.222.61):

In Reply to: Re: IH 2000 Loader-Need Advice posted by Nat 2 on December 09, 2006 at 15:32:25:

Hi Nat,
Wow, thanks! Excellent information. What you say makes sense.

re: operating the loader: There are 3 levers mounted on the right side of the steering wheel. Two are for the loader and one for the rear blade. One of the two operates the arms and the other operates the bucket. Okay, now going to explain how its hooked up. I do have a picture but need a close up of the right side for full viewing pleasure. lol

The hoses to these levers come from what we are assuming USED to be the much lower fill pipe. It has obviously been made taller and then it tees off to the three hoses, continues up where it has a fill cap, vented nonetheless. Actually, from this point it is too hard to explain so I will stop here.

The belly lever on the right side by your shin (I assume this is what you are talking about) turns a cylinder, on the right side, that appears as tho you can bolt on a pulley. This only operates when the clutch is released and the lever pushed in.

There are also two threaded ports on each side of the belly that are capped for a total of 4 capped ports. Have no clue what those are.

I am working on putting up a page with many pictures as one sure wont do the trick. We do have an 856D that we considered putting this loader on but it doesn't seem like it is wide enough for the 856. There are spacers on the M and then very deep mounts. I don't know if the loader had been cut out because it was originally on a larger tractor.

Thanks so much for your wonderful information and I will post when I get that page up.



Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Gatherin of the Orange - by Rick Nikolich. In July of 1998 I was talking to fellow Allis Chalmers collector Mike Schilling about the annual "Gathering of The Orange" AC show coming up in August of 1999. He got this wild idea that we should get a convoy of AC tractors and drive them from Charlotte, Michigan 105 miles to LaGrange, Indiana. ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy