Farmall & IHC Tractors Discussion Board |
Re: # 70 IHC PLOW
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Hugh MacKay on November 09, 2006 at 03:02:42 from (216.208.58.133):
In Reply to: # 70 IHC PLOW posted by Earl-IL on November 08, 2006 at 16:57:19:
Earl: Been awhile, hows the fall in Il, wee bit dryer than here I hope. I'm trying to do some plow testing, problem with this rain, I have too much time on my hands for adjustments and not enough time to see if the adjustments work. The No. 70 was 3, 4, 5 or 6 bottom starting in 1958, 14" or 16" bottom. It later became the 700 and went as high as 8 bottoms. I have an IH dealer parts book that gives a listing for 3 & 4 bottom and another for 5 & 6 bottom. I haven't looked in detail but expect there must be frame difference. IH do the same with the 60 - 2 & 3 bottom and a 3 & 4 bottom. the first one describes the 3 bottom as reducable to 2 and the second describes 4 bottom as reducable to 3. I don't see anything suggesting any of the 70s were reducable. The major difference in the 60 and 70 is frame size as it applies to clearence, both vertical and horizontal Vertical is around 26" on 60 and 30" on the 70. Horizontal is around 21" on 60 and 24" on 70. Some books will call that a bit different. I had a 4 bottom No. 60 plow and had a neighbor with a 70 4 bottom plow. Side by side the size was quite noticable. The two plows used the same trip mechanism in the trip beams, although a few of the early 60 at least had trip hitch rather than trip beams. Both plows used the same bottoms, but watch out for early models as they may have Plow Chief bottoms. IH only used those about 2 years, thus there are not many wear parts available. Plow Chief has the two piece point and share. You don't want Plow Chief anyhow, believe me I had one, trouble, trouble, trouble. The points will not stay tight. The Super Chief bottoms were far superior, came out around 1960, and every IH and CaseIH plow I've seen since still uses them. CaseIH may well be still using Super Chief bottoms, not a lot of new plows in the past 10 years, to be sure who's using what. I can assure you one thing, if it's Super Chief parts, they are still front row center at CaseIH parts dept.
Replies:
Home
| Forums
Today's Featured Article -
The Day Mom Drove the 8N - by Brian Browning. My Dad was wanting to put in a garden but couldn't operate the 8N and handle the old horse drawn plow he had found and rigged up to use with the tractor. Well, he decided to go get Mom out of the house and have her drive the tractor while he walked behind the plow. You got to understand that while my Mom is a hard worker who will always help whenever she can... she had never operated farm machinery before that day. Dad got her out there, explained how the clutch was the same as in our o
... [Read Article]
Latest Ad:
18-32 Case Cross Motor
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|