|
Farmall & IHC Tractors Discussion Board |
Re: Re: Re: Re: Cub Hydraulics
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Wardner on March 03, 2004 at 11:22:11 from (67.25.167.68):
In Reply to: Re: Re: Re: Cub Hydraulics posted by scruffy on March 03, 2004 at 09:55:57:
Scruffy, The following is an email that I sent to the addressees below. I may have priced the block too high. I would be willing to knock off $10. The block diverts 100% of the output. The Cub touch control can handle a large cylinder if it is double acting. The block was probably used on the one-arm Cub loader.
>To D. Miller and Chad.
>
>I only have one block. This puts me in the position of having to make one or listing the block on eBay. It will take me about three hours to reproduce and ship the block. The cost will be $75 and includes shipping. I have a Bridgeport miller so that is not a problem. I believe the genuine part is made from 3/4 steel plate. I would probably make the reproduction from 1" stock even though I probably have the 3/4" stock. There are approximately 7 or 8 holes on the face and one 1/4" NPT on an edge. The new piece could be made from aluminum for the same price. I can't remember if gaskets or O-rings are used to bolt it up. The pressurized fluid will have to go a small open center valve. It can be either 3-way (single acting) or 4-way (double acting). I still have the after market 4-way valve somewhere but don't know its condition. If it appears to be OK, I would let it go for $45. I might even get lucky and find the mounting plate that I made for the valve. No charge for that. I think it used the steering column flange and transmission cover bolts.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Upgrading an Oliver Super 55 Electrical System - by Dennis Hawkins. My old Oliver Super 55 has been just sitting and rusting for several years now. I really hate to see a good tractor being treated that way, but not being able to start it without a 30 minute point filing ritual every time contributed to its demise. If it would just start when I turn the key, then I would use it more often. In addition to a bad case of old age, most of the tractor's original electrical system was simply too unreliable to keep. The main focus of this page is to show how I upgr
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
