Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

Testing sparks plugs

Welcome Guest, Log in or Register
Author 
MSS3020

04-07-2008 12:56:37




Report to Moderator

I have a 2 cycle toro snowblower thats been giving me problems. Wont start. Pull plug and put back pull and starts up. Next day same thing. pull pull pull no start, pull plug, put back and starts. How would I go about checking the ignition on this snowthrower, can you do this by using a volt meter or multipurpose meter?
THanks




[Log in to Reply]   [No Email]
JT

04-08-2008 19:21:17




Report to Moderator
 Re: Testing sparks plugs in reply to MSS3020, 04-07-2008 12:56:37  
When you take plug out, what does it look like?Is it wet or dry? what do you do, just take out plug, put back in and it starts? How old is your gas? Is it over 30 days old? What plug are you using? Is there any particular thing or chain of events that happened when it started this problem? Have you checked compression? A Powerlite normally is an easy starting machine. How are you starting it? What is your procedure when cold and procedure when hot for starting?
Jim

[Log in to Reply]  [No Email]
IH2444

04-08-2008 13:26:43




Report to Moderator
 Re: Testing sparks plugs in reply to MSS3020, 04-07-2008 12:56:37  
Sure you can use a $2000 oscilliscope and a HV probe. but it is much simpler to buy a plug. I use a test leat with a big alligator clip on one end I clip aroung the plug threads and a smaller clip on the other end I clip to the block. get out of the sun , pull the cord and look for a nice little spark. If not there I change the plug, if still no spark I check the points, mag coil, etc...



[Log in to Reply]  [No Email]
buickanddeere

04-07-2008 17:51:14




Report to Moderator
 Re: Testing sparks plugs in reply to MSS3020, 04-07-2008 12:56:37  
New non resitor plug such as a Autolite 216.
Vibration from small engines can shake the restance internals apart just enough to provide a phantom proble.



[Log in to Reply]  [No Email]
RobMD

04-07-2008 16:12:49




Report to Moderator
 Re: Testing sparks plugs in reply to MSS3020, 04-07-2008 12:56:37  
spark arrestor on the muffler anywhere? If so, REMOVE IT.



[Log in to Reply]  [No Email]
guido

04-07-2008 16:00:36




Report to Moderator
 Re: Testing sparks plugs in reply to MSS3020, 04-07-2008 12:56:37  
Hello MS3020.
Take the spark plug out and gap it at.040.
If the ignition is electronic,it should start better. If you have points gap the plug at.030. New plugs need to be gapped, I would then try I new plug, gapped at .040.for electornic ignition and 030. for points, If you have good spark and it still won't start the plug will look wet when you take it out. Then you need a new one.
When it starts you need to readjust the carburetor high speed if there is one.
Guido.

[Log in to Reply]  [No Email]
Jon Hagen

04-07-2008 15:40:13




Report to Moderator
 Re: Testing sparks plugs in reply to MSS3020, 04-07-2008 12:56:37  
You might try your local TSC to see if they have the Correct E3 brand plug for your engine. I was originally suspicious of them as just being another gimick that works no better than a new standard plug, but I was wrong. I have Ryobi string trimmer and leaf blower that both had plug fouling problems, they run too rich at our altitude and the carbs have no mixture adjustment.
I was in the lawn mower department of TSC for the fourth new plug to keep that darn leaf blower starting / running. I saw the E3 plugs on the rack with the claim of never fouling or your money back. I asked the counter guy if they would honor that warrenty if this plug fouls in my leaf blower, he said they would. I must say the odd looking thimgs have performed as advertised.
I have never fouled a plug in the 2 cycle Ryobi string trimmer and leaf blower, plus they start easier and have more power.
With good luck in the two cycle yard tools, I tried them in my hard starting 17 HP Briggs powered 2 cyl lawn tractor. That one always was hard starting when cold and would misfire on one bank when lugged very hard. A new mag, wires and several sets of plugs did nothing to improve it. I put E3 plugs in it and the hard cold starting is gone, as is the heavy pulling misfire.
The silly looking things do work, have not had to mess with plugs in the lawn / garden stuff for 2 years. I dont know if TSC still has the E3 plugs, they had them terribly over priced ($7) and may have shot themselves in the foot with that high price.

I have also seen the E3 brand plugs advertised online and at auto parts stores.
Try one, I bet you like it.

[Log in to Reply]  [No Email]
david - or

04-07-2008 13:56:51




Report to Moderator
 Re: Testing sparks plugs in reply to MSS3020, 04-07-2008 12:56:37  
There may be nothing wrong with the spark plug. If the temperatures and carb setting are such that the first start attempt floods the engine, then you remove and replace the plug, you've now aired out the cylinder and dried the plug. It may be that this sequence gets the carburetor primed, so she'll start once the resulting flooded condition is cleared.



[Log in to Reply]  [No Email]
billylee

04-07-2008 13:52:16




Report to Moderator
 Re: Testing sparks plugs in reply to MSS3020, 04-07-2008 12:56:37  
Taught small engine mechanics for 31 years, if you get a spart tester make sure you are getting a blue/white spark. Most 2 stroke no start/hard start problems are traced back to two things, spark and fuel. Bet if you get a new plug and mix up some fresh gas/oil, it will fire right up. If you are using reformulated gas, ethanol heavy, it tends to go flat alot sooner than plain unleaded regular even if you use a stabilizer. Good luck, Billy

[Log in to Reply]  [No Email]
MSS3020

04-07-2008 13:56:59




Report to Moderator
 Re: Testing sparks plugs in reply to billylee, 04-07-2008 13:52:16  
I replaced carb as the choke and throttle lever were wore out. THere is no carb adjustments on this carb either.



[Log in to Reply]  [No Email]
JT

04-07-2008 13:43:53




Report to Moderator
 Re: Testing sparks plugs in reply to MSS3020, 04-07-2008 12:56:37  
I would replace the spark plug 1st. The igntion system either works or it don't when cold. Now if it gets hot and shuts down, you might have a bad coil. What you say is happening does not make mechanical sense. So, as I said, spend $3.00 buy a spark plug, try to find someone with NGK plugs, Champions do not hold up well in a 2 cycle engine. What model snow blower are we dealing with here.
Jim

[Log in to Reply]  [No Email]
MSS3020

04-07-2008 13:52:18




Report to Moderator
 Re: Testing sparks plugs in reply to JT, 04-07-2008 13:43:53  
powerlite snowthrower model 38170. I have but new plugs in her. And brand nw carb.



[Log in to Reply]  [No Email]
dr sportster

04-07-2008 13:40:56




Report to Moderator
 Re: Testing sparks plugs in reply to MSS3020, 04-07-2008 12:56:37  
Another two stroke trick;start it with the plug cap loose.If it doesnt stall the plug is fouled.The extra voltage surge jumping the loose cap will do this by cleaning the plug as it fires and misses.



[Log in to Reply]  [No Email]
dr sportster

04-07-2008 13:35:32




Report to Moderator
 Re: Testing sparks plugs in reply to MSS3020, 04-07-2008 12:56:37  
They sell a little test light with high tension ends like a male and female plug wire end.It doesnt tell you the plugs status but it will monitor spark while you are troubleshooting everything else.When its a two stroke the plug can look clean and be fouled.Anyway the spark tester is handy.Northern tool sells a cheapo one.You will see brilliant flashhing if its a fuel problem.



[Log in to Reply]  [No Email]
Lanse

04-07-2008 13:14:23




Report to Moderator
 Re: Testing sparks plugs in reply to MSS3020, 04-07-2008 12:56:37  
do you ever have to clean that plug?? If you do, then you may need a new plug, most likely a hotter one.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy