Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

Took Micrometer Apart

Welcome Guest, Log in or Register
Author 
moonlite 37

01-30-2008 17:56:31




Report to Moderator

I took a moderate priced micrometer apart thinking it needed cleaning. It was off about .0003 before when closed, which was good enough for my work. Now it is .002 when closed. What did i do wrong. A good machinist told me I had ruined it when unscrewing it all the way. i suggested adjusting the anvil and he told me I had already ruined it. Any help?




[Log in to Reply]   [No Email]
ollieollie1600yahoo.com

02-01-2008 23:57:56




Report to Moderator
 Re: Took Micrometer Apart in reply to moonlite 37, 01-30-2008 17:56:31  
Most micrometers are adjustable, I happen to have one junk one in my tool box that isn't though and it's off by .001" (one thousandth) It's a Lufkin, and it's probably 2x older than me but it came in a tool box I got from a past co-worker who picked it up at a rummage sale for me.

What brand is your mic? If it's a Starrett or a Mitutoyo, it's gonna be adjustable. Most others are as well, but some aren't. If you bought it new, it should have come with a wrench to adjust it, otherwise your buddy, if he knows anything about them (doesn't sound like it) and he has a set of his own mics, he should have a wrench to adjust his with. Might be the same one you need to adjust yours.

Follow the link that Little Ed posted. It's actually to the school I went to for the machine tool program and I graduated fomr there last May.

Donovan from Wisconsin

[Log in to Reply]  [No Email]
moonlite 37

02-02-2008 03:02:18




Report to Moderator
 Re: Took Micrometer Apart in reply to ollieollie1600yahoo.com, 02-01-2008 23:57:56  
Thank You, I cleaned it well and oiled and now is .0025 when dully closed. i think it may have gotten bent as it turns a bit harder than it should. I am going to go to a machine shop and borrow a standar. I did measure the shank of a new twist drill and compared the reading with another micrometer I have. I can just subtract .002 from the reading. It is at least 25 years old as I used it when is school. And is an MG made in New York. It looks nice but is a moderate priced one. The other one is all beat up but reads good. I Used the beat up one for anout 14 years to measure sheet thickness. The beat up one has an adjustable anvil. I used to measure sheets and forget and carried in pockets or left on a desk top.

[Log in to Reply]  [No Email]
Don-Wi

02-02-2008 05:32:37




Report to Moderator
 Re: Took Micrometer Apart in reply to moonlite 37, 02-02-2008 03:02:18  
third party image

Just a thought here, but did you happen to touch the collar that"s under the thimble? If you moved that one way or the other, that affects the feel of the micrometer, making it tighter or looser to turn.

The best lubricant for micrometers and other measuring tools is either the oil that Starrett sells, or plain old WD-40. I clean mine off with electronics cleaner and then spray them down liberally once in a while.

Donovan from Wisconsin

[Log in to Reply]  [No Email]
onefarmer

01-31-2008 17:32:29




Report to Moderator
 Re: Took Micrometer Apart in reply to moonlite 37, 01-30-2008 17:56:31  
Dang, The first thing they taught us in high school auto class was to check the calibration of the mic and how to reset it.

You good machinist might be "good" but is far from great if he says you ruined it.



[Log in to Reply]  [No Email]
Bob - MI

01-31-2008 09:29:01




Report to Moderator
 Re: Took Micrometer Apart in reply to moonlite 37, 01-30-2008 17:56:31  
You may have something on the anvils. Take a piece of paper and clamp in in the mic. Pull the paper out and repeat a couple of times. If it's still off hold the mic up to the light and make sure you can't see any light through the anvils with them closed. If they are completely closed and it shows off you will have to adjust the barrel until you get zero again.

I would question any machinist who doesn't know how to re-set a micrometer. If you can't get it set right you can have it re-calibrated. There's someone in your area who does that I'm sure.

Are these digital mics?

[Log in to Reply]  [No Email]
bobi

01-31-2008 06:29:43




Report to Moderator
 Re: Took Micrometer Apart in reply to moonlite 37, 01-30-2008 17:56:31  
You will need to get a standard to set it right. Most sets come with one but indivuals won,t A mike propoprty set will give you accurate measurements needed to do detailed work Most times once set are good for long peroid of time if not dropped etc. As far as being off .003 that is railroad standards ha If you know for sure what it is off you can allow for it in measurement



[Log in to Reply]  [No Email]
Larry Condon

01-31-2008 06:15:13




Report to Moderator
 Re: Took Micrometer Apart in reply to moonlite 37, 01-30-2008 17:56:31  
Most mics come from the factory +/- .0002-.0003 setting. You can hold them in your hand for a few minutes and body temp will change that tolerance.

Larry



[Log in to Reply]  [No Email]
Spook

01-30-2008 21:22:59




Report to Moderator
 Re: Took Micrometer Apart in reply to moonlite 37, 01-30-2008 17:56:31  
All of them are adjustible. The thread is a special 1:40 if I remember. Look in your Machinery Handbook for instructions.



[Log in to Reply]  [No Email]
old timer in ohio

01-30-2008 20:49:59




Report to Moderator
 Re: Took Micrometer Apart in reply to moonlite 37, 01-30-2008 17:56:31  
Hey there moonlite;
Retired as millwright,I think your"good
machinist" should go back to school!Any
(or almost any),precision micrometer is
adjustable.As I have said before there are very few "true mechanics"today they are just parts changers.Bob
God Bless



[Log in to Reply]  [No Email]
Little Ed

01-30-2008 19:33:34




Report to Moderator
 Re: Took Micrometer Apart in reply to moonlite 37, 01-30-2008 17:56:31  
go to its.fvtc.edu/machshop1/inspection/AdjustMic.htm or just google adjust a micrometer. You can read it easier than we can type it. HTH



[Log in to Reply]  [No Email]
landlord7012

01-30-2008 18:53:30




Report to Moderator
 Re: Took Micrometer Apart in reply to moonlite 37, 01-30-2008 17:56:31  
Assuming you did not remove the anvil and that you unscrewed the thimble - Most O.D. mics are adjustable by turning the thimble sleeve using a small spanner wrench that should have came with the mic. Assuming you took it apart and handled it with care and only cleaned it with denatured alcohol (or similar)and a lint free cloth, no harm was done by taking it apart - as Bob said they are meant to be taken apart to clean and adjust. One other word of caution: nowadays just because one is a "good machinist" doesn't necessarily mean they know anything about the inner workings of gages and the like. I work with a few CNC Jockeys that call themselves "machinist".

landlord7012

[Log in to Reply]  [No Email]
Bob/Ont

01-30-2008 18:27:14




Report to Moderator
 Re: Took Micrometer Apart in reply to moonlite 37, 01-30-2008 17:56:31  
Someone put it together didn't they? You should have a hook wrench to turn the barrel and line up the zero when closed. I sugest getting some gauge blocks and checking it through out it's range. Make sure the tips are clean and there is a feel for measuring with them or use ratchet.
Later Bob



[Log in to Reply]  [No Email]
Bob

01-30-2008 18:10:20




Report to Moderator
 Re: Took Micrometer Apart in reply to moonlite 37, 01-30-2008 17:56:31  
Adjust it. Typically, there's a lockscrew in the thimble, allowing it to be set back to "zero".



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy