Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

Stihl 034 running poorly

Welcome Guest, Log in or Register
Author 
oldiron29

01-10-2008 04:55:16




Report to Moderator

I was out cuttting wood and my saw died. I have cleaned air breather and was able to restart saw. It would not run at idle and seemed to starve for fuel at high rpms I play with adjusments. Got it running again for a while but died again. I am going to pull and clean carb today. What is LA setting for? What should I set for basic start settings on all 3 screws?
Thanks for any help. oldiron29

[Log in to Reply]   [No Email]
mad farmer

01-10-2008 06:09:59




Report to Moderator
 Re: Stihl 034 running poorly in reply to oldiron29, 01-10-2008 04:55:16  
Hi/lo settings are 1 turn out from full in (to start off), the other carb screw is idle rpm. The proper way to set hi setting is with a tach, otherwise you set it rich under full throtle with no load (4 strokes/stumbles a bit). Lo setting effects idle and acceleration off idle.

Check fuel line and filter, screen inside carb, diaphragm in carb to start. If you are getting fuel then check for air leaks at impulse line and carb/carb boot. The other main source of leaks is the crank seals but a you might need a dealer to check this.

Another thing that is quick to check is a scored piston, pull muffler with T27 torx and look through exhaust port. Can also check compression, 140 is marginal/OK, 150-160 is good.

Another thing to check is ignition/switch for shorts.

[Log in to Reply]  [No Email]
oldiron29

01-10-2008 15:36:12




Report to Moderator
 Re: Stihl 034 running poorly in reply to mad farmer, 01-10-2008 06:09:59  
Mad, You got it I pulled the muffler piston is scored. I pulled it all do Jug is ok I can clean it up I need a piston and rings. I checked with my stihl dealer they are on back order for months. Does anyone no a good source for aftermarket parts? 25yr old 034 46mm piston Thanks oldiron29



[Log in to Reply]  [No Email]
mad farmer

01-11-2008 07:33:25




Report to Moderator
 Re: Stihl 034 running poorly in reply to oldiron29, 01-10-2008 15:36:12  
Best piston/ring sets are OEM Stihl. A 036 jug/piston (48mm) will also fit that bottom end.

Before rebuilding try to find out why it scored: 1) bad mix/raw gas, 2) air leak, 3) lean mixture carb setting. No sense in rebuilding and having it happen again.

Aluminum from the piston on the cyl can be removed by carefully wiping with muriatic acid, do not get this on the aluminim portion of the cyl. A ball home is the best thing to use before installing new piston/rings to used cyl.

There are places that make replacement pistons, the only one I've heard universally good things about is Tecomec/PrecisionTooling.

Baileys carries aftermarket pistons/cyl but they are made in Tiawan/China

Check this website it has lots of saw info:

[Log in to Reply]  [No Email]
oldiron29

01-11-2008 13:15:16




Report to Moderator
 Re: Stihl 034 running poorly in reply to mad farmer, 01-11-2008 07:33:25  
Mad, I think I had to lean carb setting and I was cutting alot of big wood for to long and got it real hot. Stihl has 2 month back order on piston sets my 034 mics at 46mm aprently depending on the year there where 46mm and 48mm
I ordered one from baileys. We will see how it goes 34.95 piston and rings stihl 130.00 piston and rings 25 yr old saw it don't pay to put to much into it. Thanks again oldiron29

[Log in to Reply]  [No Email]
mad farmer

01-11-2008 18:25:12




Report to Moderator
 Re: Stihl 034 running poorly in reply to oldiron29, 01-11-2008 13:15:16  
I just checked ebay, too bad you have the 46mm. Someone has the 48mm for $50, OEM stihl



[Log in to Reply]  [No Email]
mad farmer

01-11-2008 16:49:00




Report to Moderator
 Re: Stihl 034 running poorly in reply to oldiron29, 01-11-2008 13:15:16  
Best of luck with the saw.

I picked up a piston/cyl assy for one of my 038 by Tecomec recently on ebay for $90. Quality seems good. I've got another I'm rebuliding with OEM stihl parts, we'll see what holds up better.



[Log in to Reply]  [No Email]
Hotflashjr

01-10-2008 05:29:53




Report to Moderator
 Re: Stihl 034 running poorly in reply to oldiron29, 01-10-2008 04:55:16  
I can't help you with the settings, but I had this problem with a Jonsered I own. It ended up being a crack in a fuel line and it was starving the saw for fuel. Same type of symptoms, it would start run for a minute, then shut off. I would check the fuel lines before you take the carb off just in case that is the issue. It will save you some time and headache if that is the cause.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy