Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

Want steel to rust

Welcome Guest, Log in or Register
Author 
Stan in Oly, WA

09-22-2007 21:29:29




Report to Moderator

I have an application where I need a newly repaired area on a larger structure to rust slightly to match the overall appearance. The repaired area goes around a column and slopes down about 30 degrees from the horizontal, so applied liquid runs off. Any suggestions about how to make this happen?

In western Washington State, getting things to rust is hardly ever the problem. As a general rule, everything that can rust will rust. I mainly want it to happen faster in this case.

Thanks, Stan

[Log in to Reply]   [No Email]
Kent in KC

09-26-2007 11:59:40




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
Put a Ford F-150 emblem on it and tell it its a fender well. You should immediately hear it begin to crumble.



[Log in to Reply]  [No Email]
alan bane

09-24-2007 18:20:08




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
If you use oven cleaner, be careful not to breathe those vapors, they about got me and I was outside.



[Log in to Reply]  [No Email]
Ron in N.E. Colo

09-24-2007 18:02:24




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
Go to grocery store and buy cheapest oven cleaner. Spray it down a couple times, wait a week, and it will look 30 years old. I got this trick from an antique dealer.



[Log in to Reply]  [No Email]
Jerry F

09-24-2007 17:50:54




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
A lot of good repies already posted.

What I have done in the past is spray vinegar on and keep repeating. Some other methods work faster but vineger is pretty safe and cheap



[Log in to Reply]  [No Email]
soundguy

09-24-2007 12:54:36




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
Bolt it to your tractor.. it should start oxidizing right away.

seriously though.. some NACL in a mater spray bottle applied daily, and perhaps some snd paper to really get down to good metal and past any oxidation that may be protecting it..

ever see the underside ( or lack therof ) of a car where they salt the roads?

Soundguy

Soundguy



[Log in to Reply]  [No Email]
RobMD

09-23-2007 19:59:05




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
Maybe I'm crazy or something, but the idea of getting something to rust is unbelievable.

I work so hard, so hard to get those calcium-pitted rims sandblasted, and someone here wants to MAKE rust.

LOL



[Log in to Reply]  [No Email]
bva

09-23-2007 19:27:19




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  

Western Washington State . Sea Water should do the trick



[Log in to Reply]  [No Email]
T_Bone

09-23-2007 15:53:07




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
Hi Stan,

Common table salt would be the safest if in a area where humans would tend to touch the area.

Chlorine would be the fastest reacting to rust common steel.

I would NOT mix common known chemicals as if you mix the wrong combination you can create a deadly/explosive gas very easy.

A damp rag with the acid powder wrapped around the area would work well. It will take years to match the existing area. Any liquid runs will show up very easy on the old area.

I would check with a chemist if you want change chemicals so you don"t get a mix you"ll regret.

T_Bone

[Log in to Reply]  [No Email]
Doug N

09-23-2007 15:50:13




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
Calcium from tractor tires.



[Log in to Reply]  [No Email]
KYfarm

09-23-2007 15:42:43




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
rub some xylene on it



[Log in to Reply]  [No Email]
135 Fan

09-23-2007 10:25:44




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
You could try using a fine sanding disc or flap wheel in an angle grinder to polish the steel shiny and it should rust pretty quick just spraying water on it. I know when parts are sandblasted if they come in contact with even the slightest moisture, they rust almost immediately. Dave



[Log in to Reply]  [No Email]
Chris Jones

09-23-2007 08:15:36




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
Put bleach in an old spray bottle and spray it on the part. Repeat as necessary. I usually use 50/50 mix bleach and water.



[Log in to Reply]  [No Email]
cophil

09-23-2007 07:19:30




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
Stan, This is the formula we have used in the high country of co. soak or spray with muriatic acid for 20 minutes, then wash with water. then soak or spray with a brine solution for 20 minutes,wash with water. then soak or spray with hydrogen proxide and the rusting will begin. Philip



[Log in to Reply]  [No Email]
richlizzy

09-23-2007 04:06:48




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
Get some 28% liquid nitrogen at your local ferilizer store. It is a sticky and oily liquid that wont run off so easily. Garuanteed it will rust anything immediately. You will have to wash it off later to stop the process.



[Log in to Reply]  [No Email]
benny2

09-23-2007 01:12:56




Report to Moderator
 To get matching Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
You are right in Wa even plastic rusts there ;)).
Now I know Wa and getting rust is not much of a problem but matching rust?? Now thats a problem! Just brush on some phosphoric acid ie (lime away, Clr) I used Lime Away for rust browning of guns, but on that, it was just the vapor, I could do in 2 weeks that normally took 6 months even in WA! ;))



[Log in to Reply]  [No Email]
02

09-22-2007 22:41:42




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
Are you trying to fool the building inspecter?



[Log in to Reply]  [No Email]
Stan in Oly, WA

09-23-2007 08:47:33




Report to Moderator
 Re: Want steel to rust in reply to 02, 09-22-2007 22:41:42  
No, but thanks for asking.

Stan



[Log in to Reply]  [No Email]
old

09-22-2007 21:49:25




Report to Moderator
 Re: Want steel to rust in reply to Stan in Oly, WA, 09-22-2007 21:29:29  
Very simple rub it down with salt



[Log in to Reply]  [No Email]
mark

09-23-2007 08:22:48




Report to Moderator
 Re: Want steel to rust in reply to old, 09-22-2007 21:49:25  
put some fertilizer on it...guaranteed to rust anything it touches! Maybe you can make a soup and slop it on.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy