Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

The best I have seen so far...

[Show Entire Topic]  

Welcome Guest, Log in or Register
Author 
Will Herring

07-29-2007 11:25:36




Report to Moderator

From northerntool, I did find one that was labeled as this:

"Northern Industrial Tools Floor Drill Press � 3/4 HP, 16-Speed, 5/8in. Chuck Size"

Speed: 210�3840 RPM

For around $200, sounds like it may be all that I need.




[Log in to Reply]   [No Email]
old

07-29-2007 13:35:05




Report to Moderator
 Re: The best I have seen so far... in reply to Will Herring, 07-29-2007 11:25:36  
That one doesn't sound all that bad. Ya its still a cheap one but unless you spend more like a grand then you will never have one that is real good but most people can't spend a grand on a drill press. The one I have cost around $150 and does what I need



[Log in to Reply]  [No Email]
Will Herring

07-29-2007 13:49:59




Report to Moderator
 Re: The best I have seen so far... in reply to old, 07-29-2007 13:35:05  
I found this one at Grizzly for about $250, perhaps it is a bit better.

* Motor: 3/4 H.P., single-phase, 110V * Overall height: 64" * Spindle travel: 3-1/4" * Number of speeds: 12 * Drill chuck: 1/8"-5/8" * Spindle taper: MT #2 * Range of speeds: 140, 260, 320, 380, 480, 540, 980, 1160, 1510, 1650, 2180, 3050 RPM * Swing: 14" * Drilling capacity: 3/4" steel * Table: Precision ground cast iron * Table size: 11-3/8" sq. * Table swing: 360� * Table tilts: 90� in both directions * Approx. shipping weight: 172 lbs.

[Log in to Reply]  [No Email]
old

07-29-2007 14:25:12




Report to Moderator
 Re: The best I have seen so far... in reply to Will Herring, 07-29-2007 13:49:59  
That one sound pretty good. The slow speed it has is very good because when drilling steel the slower you can spin the bit the better off you are.



[Log in to Reply]  [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy