Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

Welding Rod Basics

Welcome Guest, Log in or Register
Author 
J Schwiebert

03-16-2007 13:36:34




Report to Moderator

Looking for a web site to find welding rod information on numbering system. Need to sub at school Monday and want to use it for a handout.




[Log in to Reply]   [No Email]
Roland Hutchinson

03-19-2007 19:51:22




Report to Moderator
 Re: Welding Rod Basics in reply to J Schwiebert, 03-16-2007 13:36:34  
Trythis


http://www.metalwebnews.com/howto/weldrod.html



[Log in to Reply]  [No Email]
Jeremiah Huson

03-19-2007 09:56:04




Report to Moderator
 Re: Welding Rod Basics in reply to J Schwiebert, 03-16-2007 13:36:34  
As a former certified professional welder, with 2 structural steel certs, 2 nuclear certs, 3 USCG Aluminum Boat certs, and an aircraft certifacation, I would like to offer some professional advice.

as far as "rod" nbrs go here are the basics;
(all rods are 1/8" u.n.o.) All Electrodes should be kept clean and dry. A good rod oven should help. The first set of numbers refer to the Tensil strength of the filler metal.

3/32" 6013 Mild steel 11 ga.- 24 ga.
6011 unlimited used mostly as root pass rod.
7013 good multi pass all position rod if using low Hyd option.

7024 good surfacing rod (non-hardfacing) used manly in the horz and flat positions.

These represent the most comonly used Electrodes in the Welding industry. If you should have any more questions please feel free to email me or you can check out the American Welding Society's website. (www.aws.org)

Hope that this helps even thought it is a little late(you could use it for next time)

Best,

Jeremiah Huson, Associate AIA, AWS

[Log in to Reply]  [No Email]
Tim B from MA

03-19-2007 18:36:21




Report to Moderator
 Re: Welding Rod Basics in reply to Jeremiah Huson, 03-19-2007 09:56:04  
Hi Jerimiah,

Did you mean 7018 as the good all around rod as 135 Fan suggested below?



[Log in to Reply]  [No Email]
135 Fan

03-19-2007 16:10:27




Report to Moderator
 Re: Welding Rod Basics in reply to Jeremiah Huson, 03-19-2007 09:56:04  
I think you meant 7018 instead of 7013. I saw a chart on the ESAB site once that explained electrode numbers but can't rememeber how I found it. Pretty much every shop has DC welders and other than specialty rods only 3 are used. 6010 (6011 on AC) for tacking and deep penetration, dirty steel and root passes when MIG isn't practical or available. 7024 for high production flat and the odd horizontal weld. 7018 for pretty much everything else where you want maximum strength. In a pressure vessel shop all you have is 6010 and 7018 or higher strength xx18 rods. MIG and some TIG are also used. Most of the big seams are done with fully automatic submerged arc machines on special manipulators. The first 2 or 3 numbers as in 60xx 70xx or 110xx indicate the tensile strength, I.E/ 60,000, 70,000 or 110,000 PSI. Do not use the tensile strength as the only factor in deciding what rods to use. The 3rd or 4th number indicates the position the rod can be used in. 1 is all position, 2 is flat and horizontal, 3 is flat only and 4 is used for very specific rods and not very common. Although there are some large (1/4in.) rods with a 1, it is almost impossible to weld vertical or overhead with them. The last number is the most important. It tells over a dozen different characteristics of the rod. Some of these are type of current used, type of flux, type of slag, type of loading (static or dynamic) and a bunch more. There can also be more numbers and/or letters after the first set of numbers. These usually indicate different alloys put in the flux for better weld properties on specific steels. The E before the number indicates that it is an electric arc welding "electrode" but most people just call them rods. E 7018-1 is an example of a very common electrode. The -1 at the end means it has additives in the flux or coating that give it better low temperature strength than a standard E 7018. Electrodes for steels like chrome-moly can have many different types. An example might be 8018 B2L. Another example, 8018 C3 has nickel added for increased toughness. All the numbers and such can get pretty confusing but buying from a knowledgable store can be a big help. I saw once where a customer wanted a specific rod the store didn't have. The uneducated salesman tried to sell him some other rods because they only had 1 number different! In the case of 7014 to 7018 there is a huge difference. It's good to know the basics and when in doubt about what kind of steel you,re trying to weld, use 7018. Most rods are fine if kept dry at room temperature. Low hydrogen (xx18) work best if stored in a rod oven. 6010 (6011 to less extent) sometimes dry out too much. You can actually dip them in water and let them dry a bit to restore the moisture content and get them to weld properly again. They have a rougher looking bead than other electrodes but are still stronger than a lot of smoother rods. I hope this helps with understanding welding rods a little better. Dave

[Log in to Reply]  [No Email]
Jeremiah Huson

03-19-2007 17:27:05




Report to Moderator
 Re: Welding Rod Basics in reply to 135 Fan, 03-19-2007 16:10:27  
The only part that I have a problem with is the dipping of rod in the water. This introduces excess Hydrogen into the weldment and causes the micro structure to fracture under stress,and ultimatly producing failure of the weldment. This is extremly important in when failure of the weldment is on critical structures (i.e. Structural Steel, of when useing stainless to contain nuclear waste.) Water and hydrogen content should be carefully monitored at all times to reduce the risk of inclusions and stress fractures to Heat Affected Zone (HAZ). Best
Jeremiah Huson Associate AIA, AWS.

[Log in to Reply]  [No Email]
135 Fan

03-20-2007 16:05:37




Report to Moderator
 Re: Welding Rod Basics in reply to Jeremiah Huson, 03-19-2007 17:27:05  
The ONLY rods that can be sometimes dipped in water and allowed to dry or are wiped off are cellulose rods such as 6010. They are supposed to have a very slight moisture content. I think it's about 5% or .5%. I can't remember for sure but think it's 5%. Any other rods such as stainless must be kept absolutely dry. There is no 6010 equivelant in stainless. Stainless usually uses a TIG root with argon backing in the pipe. Even the instructor at technical school said 6010 can be dipped when the rods have been sitting open for a long time. He was teaching a course on obtaining your pressure ticket where your pipe has to pass 8 bend tests with no flaws using 6010 root and 7018 fill and cap. After they are dipped they have to be dried off before you use them. Alberta has the reputation of having the best pipe welders in the world. The instructor mentioned above was one of them. 7018 on the other hand weld way nicer when straight out of the rod oven but make sure you're wearing gloves to handle them. They are hot! If 7018 get wet it's usually best to just throw them out. They can be restored but are never as good as new. For most farm related welding just having them dry is sufficent. Hope this clarifies things. Dave

[Log in to Reply]  [No Email]
highlandcowman

03-17-2007 04:56:29




Report to Moderator
 Re: Welding Rod Basics in reply to J Schwiebert, 03-16-2007 13:36:34  
tractor supply catalog has a good one on page 297 of the new book may be it could be faxed to you if you don't have a book doug



[Log in to Reply]  [No Email]
Joe(TX)

03-17-2007 04:24:27




Report to Moderator
 Re: Welding Rod Basics in reply to J Schwiebert, 03-16-2007 13:36:34  
I think this is what TomTX was talking about.



[Log in to Reply]  [No Email]
TomTX

03-17-2007 02:35:20




Report to Moderator
 Re: Welding Rod Basics in reply to J Schwiebert, 03-16-2007 13:36:34  
Can't remember the exact website, but its Lincoln, has more than you would ever need. Tom



[Log in to Reply]  [No Email]
Jim Kruft

03-16-2007 13:46:57




Report to Moderator
 Re: Welding Rod Basics in reply to J Schwiebert, 03-16-2007 13:36:34  
Link



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy