Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

TIG 300/300 a buzzin

Welcome Guest, Log in or Register
Author 
Tim B from MA

03-13-2007 05:57:38




Report to Moderator

I got my recently purchased Idealarc TIG 300/300 wired last night - according to the manufactureres recommendations (except have not grounded the frame yet - hopefully tonight).

When the circuit to the machine is energized, but the power switch on the machine is off, it buzzes very loudly. Does anyone think this is an issue that may be a problem and could be corrected?

My sense is that this is not out of the ordinary - it is a big machine and I know that our old clothes drier used to buzz when off, and so do our garage door openers.

Also, when the power switch is off, the frame has about 2 volts AC potential in it (measured from the frame to ground, or to neutral). I will be providing a separate ground from the frame to a grounding rod, but again just looking for opinions as to whether this seems like a problem that needs fixing.

Otherwise, it welded real nice during my trials last night (stick only, need to get an argon tank for the TIG side.)

Tim

[Log in to Reply]   [No Email]
Tim B from MA

03-16-2007 09:47:48




Report to Moderator
 Re: TIG 300/300 a buzzin in reply to Tim B from MA, 03-13-2007 05:57:38  
Dave, Keith,

Thanks for the advice. The operators manuals and parts lists for these machines, including the older ones (mine is a 1975), are now available on the Lincoln web site, but not the schematics. One of those will be handy so I will look into gettin one from Linoln or via my local supplier.

I do have a foot amprol. I have not done TIG before but an looking forward to it. I'll need to wait a couple weeks for the argon bottle - the wife is still smarting a bit from the $$ spent.

I have done several hours gas welding based on advice on this BB - mostly from T-Bone, and as I understand it, there are lots of similarities. I'm sure I will have questions as I go along.

Re: cleaning, I think I will do my best with some kind of solvent in a spray bottle and with lots of rags - maybe staight methanol will do.

RE: the buzzing from the auxillary transformer - the manual is a bit unclear, but is seems to say there is supposed to be power to the 115 outlets when the machine is turned on - is that true for your machines? I don't know yet as the fuse for mine is out - need to get a new one.

[Log in to Reply]  [No Email]
KeithF

03-16-2007 10:32:05




Report to Moderator
 Re: TIG 300/300 a buzzin in reply to Tim B from MA, 03-16-2007 09:47:48  
Yes, when the contactor closes the 110v outlets are working. In fact, that is how I run the water cooler pump for my TIG torch. If a TIG torch came with your machine, you will notice it is either gas or water cooled. If water cooled, the welding machine has a relay controlled valve to run tap water. I chose, however, to build a recirculating water cooler pump with reservoir to cool the torch. I more or less copied a commercial setup. You will enjoy using the TIG, but it requires some setup to make a smooth operation of it. I made an undercarriage for mine with wheels to roll it around. On to this carriage I mounted a shelf to keep the argon bottle with the welder when I rolled it around. My little pump and reservoir unit is on wheels also to make everything moveable. All this because the thing about TIG is that the more one can do in a sitting position the better. So the machine is mobile to get it where it allows a good welding position.

[Log in to Reply]  [No Email]
Tim B from MA

03-16-2007 12:24:56




Report to Moderator
 Re: TIG 300/300 a buzzin in reply to KeithF, 03-16-2007 10:32:05  
My machine came with a water cooled torch, No water cooler so it just had tap running through it.

Does your water coller have a compressor/condenser like a fridge, or is it just fan cooled?



[Log in to Reply]  [No Email]
Jeremiah Huson

03-19-2007 10:17:17




Report to Moderator
 Re: TIG 300/300 a buzzin in reply to Tim B from MA, 03-16-2007 12:24:56  
The buzzing is strange you should in my professional opion (I was a professional welder for seven years, now I am a drafter). As far as the water cooler, you should be adding propolyn glycol to the water this will keep it from freezing and helps prevent corrosion within the machine itself.



[Log in to Reply]  [No Email]
KeithF

03-16-2007 13:56:42




Report to Moderator
 Re: TIG 300/300 a buzzin in reply to Tim B from MA, 03-16-2007 12:24:56  
Most of the commercial units are just small pumps with a large reservoir. That is what I made. It is about a 7 or 8 gal. reservoir with a small pump and a 1/4 hp. motor. It has a pop off valve type pressure regulator to keep the pressure around 60 psi. and a return from that valve to the tank. It takes a lot of welding to heat up that amount of water, especially a home unit. I added a little antifreeze to keep the corrosion and evaporation in check. The commercial unit I looked at used a small gear type brass bodied pump. I found a used one on an oil circulating unit and proceeded to make the unit from it. I think any small circulating pump will work except it will have to develop at least 50 psi to push it through the small hoses and it will have to be regulated to return any extra volume to the tank to keep from stalling the pump/motor. The gear types work well because they are high pressure-low volume. I turn the pump on prior to using the torch as the welder will not allow the current to flow without water flow to the torch. All this was because I did not have a drain nearby to run water into, so I made a recirculating unit.

[Log in to Reply]  [No Email]
KeithF

03-16-2007 06:05:38




Report to Moderator
 Re: TIG 300/300 a buzzin in reply to Tim B from MA, 03-13-2007 05:57:38  
I have one of these welders also. They are good machines. When I got mine, I took the top and panels off and blew out all the dust and dirt I could. This one luckily did not have any greasy film on it. So that may be your biggest problem in cleaning it up. I would be careful in using water on that unit as I would think it would take many days to safely dry it out completely. If that circuit board shorts out, look out wallet. When I got mine I looked at the Lincoln website for my model. They only had manuals for the most recent models (this one was made in 1984). So I called the local weld supplier and got the number of the Lincoln salesman he dealt with. When I called him he sent me a free manual. It contains a parts list and wiring schematic. You will need the model no. and serial no. to get the right manual for your machine. My machine does not buzz until the power switch is turned on and the large contactor makes up. So I think you have it right in that the problem is located at the power to the 110 outlet on the front as the large transformer has not been energized until the contactor closes. Since it welds fine it would make sense it is not a major problem. By the way, I have used mine as a power source for a mig welder also. It supplies the DC for the welding leads and with a little tweeking it works okay.
I assume you got the foot remote for TIG welding?
Get the manual and it will explain the settings for tig and the water/gas control valves built into the machine. If you have any questions just email.

[Log in to Reply]  [No Email]
135 Fan

03-15-2007 16:01:05




Report to Moderator
 Re: TIG 300/300 a buzzin in reply to Tim B from MA, 03-13-2007 05:57:38  
Some welders do buzz a little but not usually when turned off. The high frequency will buzz as well. I don't think I'd be putting any pressure washer to a welder. This is an older machine with older electronics. I would try something like castrol super clean in small amounts to loosen any crud and then an air nozzle. If that didn't work, I'd try scrubbing with a small brush or tooth brush. Most welders aren't designed for use in a moisture environment and especially a TIG machine. Lincoln and other makers make special machines for high moisture locations. Dave

[Log in to Reply]  [No Email]
Glardon

03-15-2007 12:10:51




Report to Moderator
 Re: TIG 300/300 a buzzin in reply to Tim B from MA, 03-13-2007 05:57:38  
I would not use lacquer thinner. If it is that grimy then use an engine degreaser and then wash it out good. Do not spray any pc boards with the degreaser and if using a pressure washer, do point the nozzle end directly on the components in the welder. Stand back a foot or two so as you do not cause any damage. You can fire away at the sides, frame etc., but be careful with the transformer, weld and otherwise. AND I CAN NOT STRESS THIS ENOUGH..... let the unit dry for at least 3 days before hooking it up to the wall and turning it on!!!! Unfortunately xfmr buzz is not something that I know how to fix on small ones. Usually blowing or washing may quell the buzz, but it will never completely disappear.

Contactors are very distinctive in shape. Depending on your vintage they can be large or medium in size. They are usually square to rectangular in shape. Even in old Lincoln manuals they still call them contactors. Play around with your remote and you will be able to hear them clunk. When turning on and off your welder, if you have an input contactor, you will hear it clunk on and off with the on/off switch.

[Log in to Reply]  [No Email]
Tim B from MA

03-15-2007 13:35:34




Report to Moderator
 Re: TIG 300/300 a buzzin in reply to Glardon, 03-15-2007 12:10:51  
I do hear the input contactor clunk when I fire up the machine. I should be able to find it that way, same with using the remote for the output contactor.

I know that it is OK to get electronics wet as long as you dry them out before putting juice to them again ... but it makes me nervous. It certainly needs some kind of degreaser because the grime won't just blow off, or wipe off.

Thanks again for your advice.
Tim

[Log in to Reply]  [No Email]
Glardon

03-15-2007 06:14:53




Report to Moderator
 Re: TIG 300/300 a buzzin in reply to Tim B from MA, 03-13-2007 05:57:38  
I was unable to find a schematic, but I believe that unit has an input contactor, as well as an output contactor. Contactors begin to buzz when there is dust between the contact points, or there is severe arcing between them. You will need to remove the panels and blow the unit out thoroughly and you will be able to locate them and clean them up.



[Log in to Reply]  [No Email]
Tim B from MA

03-15-2007 06:49:47




Report to Moderator
 Re: TIG 300/300 a buzzin in reply to Glardon, 03-15-2007 06:14:53  
Thanks Glardon,

Since I posted this I took some more of the sheet metal off - it seems that the buzzing is comming from the auxilliary transformer, which I believe steps down the 230 or 460 volts (mine wired 230) to the 115 volt plug recepticals mounted on the face of the machine.

Any suggestions how to improve that?

I do need to give it a cleaning, unfortunately this machine was in a tightly packed (with equipment that is) machine shop, and the dust and fine filings are embedded in a thin coat of oily grime, not sure about the best way to deal with that. Thinking about using Lacquer thinner, but don't want to unravel any glued together parts.

[Log in to Reply]  [No Email]
Tim B from MA

03-15-2007 06:51:23




Report to Moderator
 Re: TIG 300/300 a buzzin in reply to Tim B from MA, 03-15-2007 06:49:47  
Also, the printed info that I have found for this machine is pretty sketchy - parts list don't seem to point out all the parts. Any suggestions how to recognize the contactors?



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy