Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

Used Steel

Welcome Guest, Log in or Register
Author 
Matt Weltz

02-12-2007 11:58:42




Report to Moderator

Wondering if anyone knows where I can find some good scrap or used steel. I need:
24 feet of 2x4 tubing with 1/4" wall thickness,
15 feet of 8" or 10" steel channel,
6 feet of 4" steel channel,
8 feet of 2" angle iron, 9.36 square feet of 1/4" steel plate,
and .4 square feet of 1 1/2" steel plate. Am building a hydraulic press for HS shop project and would like to keep costs down by getting as much used as possible. Thank you!

[Log in to Reply]   [No Email]
flying belgian

02-13-2007 17:27:01




Report to Moderator
 Re: Used Steel in reply to Matt Weltz, 02-12-2007 11:58:42  
If you have a srap metal yard nearby go wonder around if you don't find what you need go back tomorrow.



[Log in to Reply]  [No Email]
Mike M

02-13-2007 08:50:15




Report to Moderator
 Re: Used Steel in reply to Matt Weltz, 02-12-2007 11:58:42  
Dang ! how big of press you going to make ? or are you going to make a bunch of little ones ?

There isn't much to the 10 ton press I have from HF and it has worked very well with a few slight modifications.



[Log in to Reply]  [No Email]
Matt Weltz

02-13-2007 11:34:55




Report to Moderator
 Re: Used Steel in reply to Mike M, 02-13-2007 08:50:15  
At 3500 PSI the cylinder I have will put out 50 tons of press. I am planning on running it at 2500-2750 to get about 35 tons out of it. Everyone I talk to says to make it bigger that I think I may ever need because chances are, it will be too small at some point. I have talked it over with the local welder and this is the list of steel that we came up with that I need to find. I have been able to get the 4" channel and 2" angle from school. The local welder may have some 8" or 10" channel. I will probably order the tubing new and try to get the plate steel from one of the local manufacturers scrap bins.

[Log in to Reply]  [No Email]
Mike M

02-13-2007 15:23:42




Report to Moderator
 Re: Used Steel in reply to Matt Weltz, 02-13-2007 11:34:55  
WOW ! that's going to be one heck of a press !

What are you going to use that big of press for ?



[Log in to Reply]  [No Email]
Matt Weltz

02-13-2007 16:15:32




Report to Moderator
 Re: Used Steel in reply to Mike M, 02-13-2007 15:23:42  
Well, I am building it for use on our farm and eventually I will get it when my dad sells all his shop stuff and I will use it in my machining/welding shop that I hope to have someday. I am building it big because everyone says to, and when I get my welding shop, I may need to run more PSI and get 50 tons out of it so I want the frame to be big enough to handle that. I will be building this in my advanced welding and advanced machining classes at high school. Once completed, I will have it entered in the Southeast Polk Industial Vocational competition. I won last year with a T-handle tap wrench and machinist hammer set that I made last year in machining class. Hopefully I can win again this year.

[Log in to Reply]  [No Email]
msb

02-12-2007 19:16:49




Report to Moderator
 Re: Used Steel in reply to Matt Weltz, 02-12-2007 11:58:42  
Go to your nearest steel supplier and tell them what you are doing.I'll bet they will cut a real deal.You are a future customwer for them--at least that is the way they will view the situation.



[Log in to Reply]  [No Email]
Tim Casbolt

02-12-2007 17:20:16




Report to Moderator
 Re: Used Steel in reply to Matt Weltz, 02-12-2007 11:58:42  
Are you anywhere near these guys? Link



[Log in to Reply]  [No Email]
135 Fan

02-12-2007 17:05:27




Report to Moderator
 Re: Used Steel in reply to Matt Weltz, 02-12-2007 11:58:42  
When I went to high school the teacher made arrangements with a steel supplier close by to get short pieces and cut offs. They even let him go through their scrap bin. If new material was needed the school also got a deal. Scrap dealers sometimes get really good pieces. It's nothing for a big shop to "throw out" very usable pieces. If all they build is large pieces, they don't have room or want to be bothered with so called short pieces. I worked in a big tank shop and they sent a lot of plate to the scrap yard. You could check with some big fabricators. They might sell you their leftovers for scrap price. Especially for a school project. Hope this helps. Dave

[Log in to Reply]  [No Email]
old

02-12-2007 14:13:00




Report to Moderator
 Re: Used Steel in reply to Matt Weltz, 02-12-2007 11:58:42  
You would be better off finding out just how long each piece will need to be. Finding any of it in say 2o foot pieces and being used/scrap will be almost impossible and also cost you big bucks getting it that way. Figure up how long you need each piece than start looking you might find a good bit from welding shops etc that will be sold as scrap and then you can pay scrap price for it

[Log in to Reply]  [No Email]
dan hill

02-12-2007 14:02:12




Report to Moderator
 Re: Used Steel in reply to Matt Weltz, 02-12-2007 11:58:42  
If you wait to find the right scrap you will never get the job done.I buy new and always buy extra.



[Log in to Reply]  [No Email]
JMS/MN

02-12-2007 13:43:49




Report to Moderator
 Re: Used Steel in reply to Matt Weltz, 02-12-2007 11:58:42  
Since you did not list your location, how far are you willing to drive to find those several pieces? OK- That was the snappy answer, re: Location. But- check with machine shops, salvage yards, recyclers, etc. in your area. Might not find a local fellow, but ask for his contacts. Many times a small mfr has contacts for what they call 'mill ends'- ie, larger than what you want, but they sell it very cheaply. I've recently found half inch plate for 15 cents a pound, other suppliers in MN for 60 cents or so for bar stock, angle, beams, etc., while local shop gets a buck or so. Makes a big difference on a major job- like my current one- tile plow, with heavy steel.

[Log in to Reply]  [No Email]
IH2444

02-12-2007 12:27:13




Report to Moderator
 Re: Used Steel in reply to Matt Weltz, 02-12-2007 11:58:42  
Good luck but useable steel has gotten hard to find with the scrap price going up. I missed out on a load of 6 inch angle the other day. A guy had already cut about 4 tons 20 ft sticks up for scrap....



[Log in to Reply]  [No Email]
e

02-12-2007 16:50:29




Report to Moderator
 Re: Used Steel in reply to IH2444, 02-12-2007 12:27:13  
Well if that isn't enough to make a guy sick :(



[Log in to Reply]  [No Email]
IH2444

02-12-2007 20:12:24




Report to Moderator
 Re: Used Steel in reply to e, 02-12-2007 16:50:29  
Darn near brought tears to my eyes. I could have made something with that steel vs the Chinese...



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy