Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

Valve Grinder /Parts Question:

Welcome Guest, Log in or Register
Author 
Mike in MI

01-11-2007 20:12:39




Report to Moderator

third party image

My wife got me this Valve Grinder for Christmas and for the life of me I"m totally lost on what some of the items goes too and used for. I sent a photo on this.

I know what the long & short rod used for but I don,t know what the the other item used for?

This flat peace of steel with style tips on each end with a hole drilled thru it. I think it attaches to any one of the two shafts W/Drilled holes thru them. (But what is it used for?)

Correct me if I"m wrong, I think the spring is slid over the valve stem and then it place back into the valve guide in the head. right?

Now does the suction cup slide over the ends of the rods that are notched and drilled also?

I guess the mft. should of sent a diagram explaining the use of the items. So any help on this will be greatly appreciated! Thanks! Mike

[Log in to Reply]   [No Email]
Mike in MI

01-12-2007 06:35:11




Report to Moderator
 Re: Valve Grinder /Parts Question: in reply to Mike in MI, 01-11-2007 20:12:39  
Thanks Bob! You made it clear as water! I wasn"t sure what the flat peace was used for. The old Valve Grinder that my dad had only had the suction cup.
Mike



[Log in to Reply]  [No Email]
Bob

01-11-2007 20:22:48




Report to Moderator
 Re: Valve Grinder /Parts Question: in reply to Mike in MI, 01-11-2007 20:12:39  
"This flat peace of steel with style tips on each end with a hole drilled thru it. I think it attaches to any one of the two shafts W/Drilled holes thru them. (But what is it used for?)

Some old-time valves had two pin holes drilled in their tops, and the piece of steel is, more or less, a "spanner wrench", to engage the holes on the valve, and connect it to the grinder.

For valves with NO holes, the suction cup is used to "drive" the valve.


The valves in the photo below have SLOTS, instead of the 2 holes I wrote about.

Third Party Image


Clear as mud???

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy