Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

Drill bits

Welcome Guest, Log in or Register
Author 
Scott KY

11-09-2006 16:19:40




Report to Moderator

Need a recommendation for a drill bit set for general shop use. I've seen cobalt, zirconium, and titanium. What do you guys use?




[Log in to Reply]   [No Email]
wdTom

11-10-2006 19:19:38




Report to Moderator
 Re: Drill bits in reply to Scott KY, 11-09-2006 16:19:40  
Just a couple of things to add to what the others have said, which I mostly agree with. First, after you grind a drill point, stone it. Use a small fine stone and under a magnifier stone out all of the grinding marks. It will cut better and last longer, unless you chip it when using it that is. Second, get a drill point gauge. It is worth it. For years I though I could do fine without using one. Then I finally bought one and it does make it possible to do an almost perfect jot free hand grinding if you keep at it. Getting the angle and length of each flute the same without a gauge is just luck, no matter how good your eye. In the Home Shop Machinist back a year or so ago Forrest Addy had a very good article about drill shaprening and drills in general. Recomend it, and for that matter, anything he writes.

[Log in to Reply]  [No Email]
slowfolk

11-10-2006 12:48:59




Report to Moderator
 Re: Drill bits in reply to Scott KY, 11-09-2006 16:19:40  
Buy drill bits that have HSS stamped on them. Keep them sharp. Any drill that is allowed to wear the land diameter smaller at the drill point will bind in the drilled hole and possible break the drill bit.



[Log in to Reply]  [No Email]
JT

11-10-2006 07:01:06




Report to Moderator
 Re: Drill bits in reply to Scott KY, 11-09-2006 16:19:40  
I was at a steam show 4-5 years back and a fellow was selling drill bits that he claimed would drill anything. I am the eternal sceptic, don't delieve a lot of this garbage. Well I tried some bits he had, it drilled a file, a truck leaf spring, the head of a 3/4" grade 8 bolt, I do nto rememeber all he had to drill, but it was drilled using a drill press, OK, I will try then, bought 3 different bits I use a lot of. worked better than I thought, I was sold on them, I have ordered bits from him and they are the best I have ever used, do not know a brand. The man who sells them is Max Winters out of minnesota, his phone number is 800-950-3938. It is called Winter's Drill bit city. They are not cheap, but they are good bits for the money you will spend. I finally broke down this year at Mt. Pleasant and bought the set from 1/4"-1/2" set for around $125.00.

[Log in to Reply]  [No Email]
Midwest redneck

11-10-2006 02:21:10




Report to Moderator
 Re: Drill bits in reply to Scott KY, 11-09-2006 16:19:40  
Get HSS Drills (that stands for high speed steel) Which is heat treated tool steel, M series usually. The titatium is a wear resistant coating that helps keep it sharp. Cobalt drills are very good too. Carbon steel drills are cheap....dont buy them.



[Log in to Reply]  [No Email]
BigMarv1085

11-09-2006 22:59:16




Report to Moderator
 Re: Drill bits in reply to Scott KY, 11-09-2006 16:19:40  
I'm fortunate that I have 5 sets of colbalt bits. When they dull or the tips shatter, I just take them to work and they replace them for me. The main thing about drilling in steel is to keep the drill bit lubricated with oil, grease, or crisco.



[Log in to Reply]  [No Email]
MikeCatthemuseum

11-09-2006 22:07:49




Report to Moderator
 Re: Drill bits in reply to Scott KY, 11-09-2006 16:19:40  
I totally agree that drill bits are one of those "get what you pay for" items like tires. Try to get a set of Chicago Latrobe, Triumph, PTD or similar well known industrial names and you will keep them for life. Buy a set from HF to loan out, heheh. They won't ask again.

If you have a bench grinder and a handful of dull and/or broken drill bits, try to learn to hand sharpen them. Sit one of your new bits beside you as a guide to what a good grind should look like and try to copy it. You can either buy or make a drill point gage to ensure the lips are at the same angle and are the same length (both must be identical in these aspects or it'll bore an oversize hole). Make sure you grind the heel of the point back so it doesn't rub and get your rake angle right. Too steep and it burns up unless you are cutting aluminum. Too shallow and it'll rub instead of cutting. Once you get the hang of it, you'll wonder why you didn't figure this out before. My smallest diam limit for hand sharpening is about 3/16". Smaller than that the bits are too hard to grind and too cheap to be worth the effort.

[Log in to Reply]  [No Email]
hayray

11-10-2006 02:23:02




Report to Moderator
 Re: Drill bits in reply to MikeCatthemuseum, 11-09-2006 22:07:49  
That is what I do, just use my belt sander and sharpen them, I buy cheap ones I don't care, they all get dull. Takes a few seconds to sharpen them.



[Log in to Reply]  [No Email]
Gerald J.

11-09-2006 21:03:04




Report to Moderator
 Re: Drill bits in reply to Scott KY, 11-09-2006 16:19:40  
135 degree split point will drill much nicer with less force and less of a need to drill pilot holes. And they seem to run a bit cooler so the fanciest steels may not be needed.

Gerald J.



[Log in to Reply]  [No Email]
Jim WJ

11-09-2006 21:02:58




Report to Moderator
 Re: Drill bits in reply to Scott KY, 11-09-2006 16:19:40  
Lawson products has a very good
line of drill bits.



[Log in to Reply]  [No Email]
banjo

11-09-2006 20:24:15




Report to Moderator
 Re: Drill bits in reply to Scott KY, 11-09-2006 16:19:40  
I like the dewalt power point bits for general shop use.



[Log in to Reply]  [No Email]
John in CT

11-09-2006 18:45:51




Report to Moderator
 Re: Drill bits in reply to Scott KY, 11-09-2006 16:19:40  
I have a set of Snap-On Thunder bits that work well for general drilling ( I wish I could find the company that makes them for Snap-on) and a set of Snap-on cobalt bits that I ONLY USE to drill out a bolt or something where failure is not an option. The cobalt bits rarely let me down as being able to drill out a bolt or through something but they shatter very easily. I once was drilling a manifold stud and broke a new Napa bit. Bought the cobalt Snap-On set and drilled through the stud and Napa bit like butter!! Now if I could only sharpen them. When they get dull, I put them in a bin for another time and get a new replacement.

[Log in to Reply]  [No Email]
John Garner

11-09-2006 19:42:41




Report to Moderator
 ThunderBit? Like these? in reply to John in CT, 11-09-2006 18:45:51  
John --

Is this what you're looking for? >Link

Triumph>Link Twist Drill is a subsidiary of the US's largest twist drill maker, Precision Twist Drill. I don't know how much overlap there is between the Triumph and Precision lines, but I suspect that it's substantial and that you can find one or the other of these brands at a local mill supply house or from one of the major mail-order suppliers like MSC or Travers Tool.

There's another excellent drill maker that uses different brand names, Norseman / Viking. If your only local supplier handles either one of these brands but not the Precision / Triumph, I don't think you'll be disappointed with Norseman / Viking equivalents of the ThunderBit.

John

[Log in to Reply]  [No Email]
John in Ct

11-10-2006 17:30:11




Report to Moderator
 Re: ThunderBit? Like these? in reply to John Garner, 11-09-2006 19:42:41  
I think that is the one. Thanks!!



[Log in to Reply]  [No Email]
Rockyhawaii

11-09-2006 18:06:39




Report to Moderator
 Re: Drill bits in reply to Scott KY, 11-09-2006 16:19:40  
I just buy what's available at Sam's Club, because the bits are going to be borrowed and lost, or borrowed and broken.



[Log in to Reply]  [No Email]
old

11-09-2006 17:50:49




Report to Moderator
 Re: Drill bits in reply to Scott KY, 11-09-2006 16:19:40  
This is just sort of a rule of thumb thing here. The more you pay for any given set of bits the better the bits will be most likely. My self I have a couple sets of harbor frieght bits that I get by with but sure wish I could afford a better set. The set I'm talking about starts at 9/16 and goes up to 1 inch. A real good set of them would cost a mint

[Log in to Reply]  [No Email]
135 Fan

11-09-2006 19:58:53




Report to Moderator
 Re: Drill bits in reply to old, 11-09-2006 17:50:49  
Get some good HSS drill bits if you are doing a lot of drilling. SKF and Dormer are popular in machine shops. If your not doing a lot of tough drilling and you use a drill press mostly, any decent bits will work. Dave



[Log in to Reply]  [No Email]
B-maniac

11-10-2006 17:12:36




Report to Moderator
 Re: Drill bits in reply to 135 Fan, 11-09-2006 19:58:53  
Get good HSS set and learn how to sharpen them. You will have bits for a long time. I was tought in machine shop in 1968 how,and never regretted learning that. has saved me a lot of money. Used to get paid $.50 ea by the mechanics at dealership for doing their bits for them. Said they cut better than when new!



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy