Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

Why a set?

[Show Entire Topic]  

Welcome Guest, Log in or Register
Author 
John Garner

12-14-2005 12:56:20




Report to Moderator

bob --

A good tap and die set is very expensive, and very few people use all of the pieces. It might be wiser to buy just the pieces that you know you'll use, with extras of the ones you'll use the most, and leave the once-in-a-blue-moon stuff in the store until you actually need it.

I would suggest buying only ground-thread spiral-point taps made of high-speed steel for general use. The spiral-point tap is intended to be machine driven, and the point is ground to push the chip down the hole ahead of the tap. Because of this, the tap works best if the hole is drilled all the way through the workpiece or, if blind, substantially deeper than the thread will be cut. On the other hand, the tap won't choke on its own chips . . . there's none of the half-a-turn-forward-and-half-a-turn-back rigmarole, just turn the tap into the hole.

Good taps are available from any mill supply house, including the mail order houses such as J&L Industrial, MSC, and Travers Tool, but won't be found at any normal hardware store or tool truck. Brands to look for -- in no particular order -- would include Brubaker, Regal Beloit, OSG, Sosner, Reiff & Nestor, Uhring, Union-Butterfield, Hanson-Whitney, Morse, Greenfield, Emudge, and probably others that escape me at the moment.

When it comes to dies, adjustable dies are better than non-adjustable BUT carry with them the possibility that a thread cut with a too-open die won't fit a tapped hole. I think all of the companies I mention for taps except Reiff & Nestor make dies.

Unless you have good ones already, buy yourself good tap wrenches and die stocks while you're spending money. General Hardware's tap wrenches are superb for the price, but there are other good brands also.

John

[Log in to Reply]   [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy