Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

Drilling stainless steel

Welcome Guest, Log in or Register
Author 
Johnski

10-07-2005 12:25:54




Report to Moderator

I have to drill some 11ga. 304 stainless steel on a sander body. About 30, 1/8" holes and a few 3/8". I only get about two 1/8" holes and the drill is dulled. Any good ideas on drill speed,lubricants,etc.? I tried cutting oil but it seemed worse and way more heat, drill tip was blued.

P.S. I tried to order a box of 1/8" holes from Fastenal but they are backordered. ;>)




[Log in to Reply]   [No Email]
broker farmer

10-10-2005 07:50:18




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
I use a concrete bit and hammer drill. Worked very well for me drilling 1/2" holes in stainless steel hog feeders.



[Log in to Reply]  [No Email]
Johnski

10-08-2005 15:17:13




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
Thanks for all the feedback. I'll try out some of these ideas at work Monday. I think some new bits,a slower drill motor and a thicker lube should help. I need to stand on a ladder to drill holes around the top edges of the sander body which is sitting on 4 55gal. drums so a drill press is kinda out of the question. Again, thanks for taking the time to help, you guys are great..
JF



[Log in to Reply]  [No Email]
Steve Crum

10-08-2005 09:35:17




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
I drill literally hundreds of holes in various gages of stainless a year, many with holesaws. The best thing is as many have stated SLOW rotational speed! Upto 4" diameter I use 60 RPM and Ridgid brand threading oil (the stainless type.
I've cut as many as 80 holes in 11 gages stainless with one hole saw. and a hundred with one spiral bit. The key is a good bit or saw to start with and steady but not excessive point pressure. You should see cuttings coming off the tool at all times. If not, you need to change or sharpen the bit. As long as the bit is cutting effectively, excessive heat build up is not happening.
For a lot of holes in sheet stock these days, I cheat and put it on the CNC plasma table, then just ream the holes to the correct size.

[Log in to Reply]  [No Email]
dr.sportster

10-08-2005 05:51:54




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
Once you start do not stop to rest or the workpiece workhardens and starting again is tougher.On a hole saw you can stop and rest but spiral bits cause a workhardening effect.In a food plant they will insist on a lard based product to lube like Anchorlube.



[Log in to Reply]  [No Email]
Bus Driver

10-08-2005 04:33:26




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
I think wdtom has offered good advice. I once drilled 300 holes in 11 gage stainless with only three bit sharpenings. A drill press is the answer. Keep lots of steady pressure on the bit. Use slow speed. Most any kind of machining coolant will help a lot.



[Log in to Reply]  [No Email]
ntmcj

10-07-2005 21:57:07




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
might try pilot drilling with a good 3/32 or so. Also, try split tips. They don't make quiet as pretty hole, but they cut like crazy and last fairly long.



[Log in to Reply]  [No Email]
T_Bone

10-07-2005 21:34:19




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
Hi John,

I don't know how many thousands of holes I've drilled is SS but it's a bunch. We tried every thing for cutting oil and only a couple worked very well. One was Rapid Tap, and the other I can't remember, but a tube soap wax. These two worked well while on a drill press where you can hold vertical very well. Slower speed with adaquote down pressure.

However, cutting oils didn't work well in the field as it took two men to drill one hole. One to drill and one to squirt the rapid tap. Sounds like a new joke. LOL

Then we stumbled onto a new method. Using a 3/8" VS drill motor we would vary the drilling speed by bumping the switch from approx 1000rpm then let motor RPM drop to about 200rpm then bump the switch again back to 1000rpm, repeat until the hole is drilled with using heavy drill pressure. If the bit smokes, stop and get a new one.

This method yields about 30 to 40 holes from a 1/8" to 1/4" HSS drill bit without using any lubericant for drilling 304SS.

T_Bone

[Log in to Reply]  [No Email]
wdtom

10-07-2005 19:44:03




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
Some years ago I worked in a shop that made sailboat rigging, lots of stainless drilling involved. It is where I learned to sharpen drills free hand, you do a lot of drill sharpening when drilling stainless. The secret is to have a sharp drill, make it cut, use a slow enough speed so it doesn't heat up too much-try to keep it from smokeing, and use some oil, even engine oil is better than dry. Stainless work hardens as it is cut, every time the cutting edge of the drill comes around again you want it cutting deep enough so it is below the work hardened surface it made on the last pass, that is why you need a lot of pressure to make the drill cut. As soon as the drill dulls it doesn't cut well, heats more, doesn't get below the work hardened surface,dulls more, and on and on until you have a red hot tip, smoke, and a very hare surface for the next drill to try and get through. Keep them sharp is the secret!! At the first sign of dulling sharpen or get another drill.

[Log in to Reply]  [No Email]
SS drilling technique

10-13-2005 17:56:24




Report to Moderator
 Re: Drilling stainless steel in reply to wdtom, 10-07-2005 19:44:03  
First drill 1/8" pilot hole,using very heavy pressure, and very slow speed. Ideally you should see a spiral of material when using the correct pressure and speed.Use a little westlube also.Next using the same technique use the size drill bit needed. I have good luck with this method using standard metal cutting drill bits in up to 1/2" 316 stainless steel, 1 bit should drill at least 20 holes (actually more are easily possible with good technique).

[Log in to Reply]  [No Email]
john d

10-07-2005 18:24:39




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
Stainless can be nasty to drill. Success is enhanced with good lubrication and keeping the drill cool. The material, depending in part on the particular stainless alloy, tends to work-harden. Turn the speed down, and put enough pressure on the drill to make it CUT, not scrape its way through. A spiral chip coming off that drill is better than making dust-sized particles.
Solid carbide drills are available from tool stores and are not very expensive in the smaller sizes, especially when down-time for sharpening HSS bits is considered.

[Log in to Reply]  [No Email]
KIP in MX

10-07-2005 16:53:50




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
third party image

We use Boelube paste. Buy a little tub of this and after you use it, you won�t drill any metal without it.



[Log in to Reply]  [No Email]
Mike M

10-07-2005 15:22:06




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
You can always use some of those carbide tipped masonary bits to drill hard stuff most places carry them and not too high priced.



[Log in to Reply]  [No Email]
Richard H.

10-07-2005 15:16:56




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
I have drilled a lot of stainless over the years and the trick is to use a LOT of oil, not cutting oil it is to thin although it is good for cutting threads. When you see milling done on T.V you see them flooding the tool and object with a white milky fluid which is usually a water-oil mix. Take your time and let the bit do it"s job. Good luck, Richard



[Log in to Reply]  [No Email]
Russ Smart

10-07-2005 15:13:01




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
Turpentine used to be the recommended coolant for drilling stainless, but now there are some better ones out there, we used to use one called key-tap, worked great but kind of smelled like turpentine! We now use a paste that I don't remember the name of but it works well. The gold colored drills from Fastenal work great, but go slow.



[Log in to Reply]  [No Email]
Scott-Sd

10-07-2005 14:27:29




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
You can try using bleach when your drilling. Thats what they used at where I used to work. But the bits still went dull.



[Log in to Reply]  [No Email]
steve in in

10-07-2005 13:44:58




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
I believe cobalt steel tips are what you need. They are more expensive, but if you treat them well they last a long time.



[Log in to Reply]  [No Email]
Fawteen

10-07-2005 12:42:49




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
Someone who knows more will no doubt be along directly, but for now, I'm pretty sure the bit angle on drills for stainless is steeper than for mild steel. 135o sticks in my mind, but don't quote me on it.



[Log in to Reply]  [No Email]
Fawteen

10-07-2005 12:42:30




Report to Moderator
 Re: Drilling stainless steel in reply to Johnski, 10-07-2005 12:25:54  
Someone who knows more will no doubt be along directly, but for now, I'm pretty sure the bit angle on drills for stainless is steeper than for mild steel. 135o sticks in my mind, but don't quote me on it.



[Log in to Reply]  [No Email]
Patrick Kane

10-07-2005 13:24:20




Report to Moderator
 Re: Drilling stainless steel in reply to Fawteen, 10-07-2005 12:42:30  
Hi. Put a gobb of white glue where you are going to drill, drill slow the glue will follow the bit and keep it cool, i've drilled as many as 50- 1/8 holes with one bit.



[Log in to Reply]  [No Email]
Angle Iron

10-07-2005 14:58:13




Report to Moderator
 Re: Drilling stainless steel in reply to Patrick Kane, 10-07-2005 13:24:20  
I used to drill a lot of holes for pop rivets in ss steele. Split tip bits, slow speed and crisco cooking shortining. Dip the bit in,it will hold some in the spirals. If the bit gets too hot to hold the crisco just keep it in there until cool enough to do so. It workd as a self feed cuting fluid. Speed is really a factor. If you don't have a variable speed drill just keep bumping the trigger to keep the speed down.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy