Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

Throw-Out Bearing Growl

Welcome Guest, Log in or Register
Author 
Joe in Minnie

02-05-2005 10:50:13




Report to Moderator

I have an ole 1971 Dodge D300 1 Ton with a 318 motor and stick shift, it has only 32000 miles on it, over the past years, I'v changed the Throw-Out Bearing cause it Growled, I first changed it at about 20,000 miles, then about 30,000 I changed it again, then about 31,500 I changed it, and now after less then 500 miles it's growling, Now keep in mind, after the bearing gets warmed up, it stops growling, but only the first few miles (when cold) I leave the Cluch out, "it just growls." after taking the bearing out, it looks just fine, no play and no grind, but in the truck is growls, (the shaft looks stright as an arrow) the mechanic that replaced it, says, just run it, it can hurt, has any one had this problem in the past? it's just a pain to live with a Growling Women.... thanks for your help. Joe

[Log in to Reply]   [No Email]
IHC Red

02-06-2005 18:34:17




Report to Moderator
 Re: Throw-Out Bearing Growl in reply to Joe in Minnie, 02-05-2005 10:50:13  
I had a '74 1/2 ton with a 318 4-speed. I had trouble after the clutch was replaced. They put in what must have been a poor quality pilot bushing and I had to have it re-installed. It growled as you describe.



[Log in to Reply]  [No Email]
Fred Kobs

02-06-2005 03:15:01




Report to Moderator
 Re: Throw-Out Bearing Growl in reply to Joe in Minnie, 02-05-2005 10:50:13  
Have you changed the pilot bearing/bushing??



[Log in to Reply]  [No Email]
msb

02-05-2005 16:43:40




Report to Moderator
 Re: Throw-Out Bearing Growl in reply to Joe in Minnie, 02-05-2005 10:50:13  
You might want to check the finger height of the pressure plate to see if they are all even. I am not familiar with the truck in question,but if the fingers are not even it could cause the bearing to put into a bind with most of the load concentrated in only one spot on the bearing surface.FWIW,bob



[Log in to Reply]  [No Email]
lucasss

02-05-2005 15:21:20




Report to Moderator
 Re: Throw-Out Bearing Growl in reply to Joe in Minnie, 02-05-2005 10:50:13  
i am 100% sure that yor throwout brg is not supposed to touch the pressure plate with your foot off the clutch pedal..lucas



[Log in to Reply]  [No Email]
Roger in St.Louis

02-05-2005 14:34:15




Report to Moderator
 Re: Throw-Out Bearing Growl in reply to Joe in Minnie, 02-05-2005 10:50:13  
you hae a 71 dodge with only 31000 miles on it and you wonder why the t/o bearing is growling? Dry rot come to mind? I know the t.o brg is sealed but it is over 30 years old. Like they say, the brg should not be in contact with the clutch unless the pedal is depresed but then the pedal is depressed because it is over 30. :)



[Log in to Reply]  [No Email]
Allan in NE

02-05-2005 14:38:22




Report to Moderator
 Re: Throw-Out Bearing Growl in reply to Roger in St.Louis, 02-05-2005 14:34:15  
Rog,

Read it again. He's changed the throwout bearing three times and the latest has only 500 miles on it. :>)

Allan



[Log in to Reply]  [No Email]
Allan in NE

02-05-2005 14:25:19




Report to Moderator
 Re: Throw-Out Bearing Growl in reply to Joe in Minnie, 02-05-2005 10:50:13  
Joe,

Does the noise go away when you press the clutch?

If so, I don't think it is the throwout bearing at all.

Those old transmissions used carbon steel "bushings" on the mainshaft that the speed gears idled on and they were forever making that "growling" noise.

If the noise changes with different gears or if it shuts up with one certain gear, I kinda think that these bushings are your problem rather than the throwout bearing.

Allan

[Log in to Reply]  [No Email]
Opa A

02-05-2005 14:02:37




Report to Moderator
 Re: Throw-Out Bearing Growl in reply to Joe in Minnie, 02-05-2005 10:50:13  
Being a 1971 D300 I imagine it has mechanical clutch linkage, my book says D400 & up have hydraulic clutch release. There must be about 1/8" clearance between the face of the release bearing and the clutch release levers. Usually about 1 1/2" free pedal before bearing contacts levers. Also check for broken or missing springs used to hold release fork tight to lower bellcrank (Keep tension on adjusting rod). It may also have a spring clip on the back of the release fork to keep it located on the pivot ball. My 2 cents

[Log in to Reply]  [No Email]
Bob

02-05-2005 14:07:19




Report to Moderator
 Re: Throw-Out Bearing Growl in reply to Opa A, 02-05-2005 14:02:37  
Good ideas, Opa A!



[Log in to Reply]  [No Email]
Charles (in GA)

02-05-2005 12:59:10




Report to Moderator
 Re: Throw-Out Bearing Growl in reply to Joe in Minnie, 02-05-2005 10:50:13  
Bob is correct, a '71 model most certainly has a old time clutch linkage that requires free play at the top of the pedal travel. The bearing should not be touching the pressure plate fingers when the clutch is released.

Charles



[Log in to Reply]  [No Email]
Bob

02-05-2005 11:19:18




Report to Moderator
 Re: Throw-Out Bearing Growl in reply to Joe in Minnie, 02-05-2005 10:50:13  
Is it a self-adjusting clutch, where the throwout bearing always contacts the pressure plate finger, and always runs?

If it is NOT a self-adjusting clutch, and has pedal "free travel", the bearing will not be contacting the clutch fingers, and should NOT be turning all the time, and making noise.

You may have a defective or mis-adjusted pressure plate, with the fingers set at different heights.

If it is NOT a self adjusting clutch, the throwout bearing should NOT be running with the clutch pedal released. If this is the case, you may have a bearing in the transmission that's making noise.

Throwout bearings, obviously, are under LOAD when the clutch pedal is DEPRESSED, and this is when most bad throwout bearings will make the most noise.

[Log in to Reply]  [No Email]
MAC,IL

02-05-2005 11:16:30




Report to Moderator
 Re: Throw-Out Bearing Growl in reply to Joe in Minnie, 02-05-2005 10:50:13  
Maybe I am missing something, but seems the T/O bearing Shouldnt make a noise when there is no load on it unless it is way out of adjustment and is constantly engaged by the fork. Seems thats to many bearings to replace. I would look about the adjustment first thing and then look at the front trans. Bearing. How about the pilot bearing or bushing whichever applies to that model? Are all the pressure plate springs up to par?

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy