Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

Weld positioner speed

Welcome Guest, Log in or Register
Author 
Slowpoke

05-26-2004 01:24:47




Report to Moderator

Approximately how many inches per minute would one use to weld a 4" OD, 1/4" wall steel pipe to a 1/4" flat plate base? I am guessing about 48". Are there any charts or formulas to figure rotational speed? I will be using a mig welder, the pipe end will be beveled.




[Log in to Reply]   [No Email]
Slowpoke

05-27-2004 15:13:57




Report to Moderator
 Re: Weld positioner speed in reply to Slowpoke, 05-26-2004 01:24:47  
I forgot one small detail on my welding rotator....the welding ground lead. I could probably make some kind of slip connection to the turntable drive shaft. The motor drives it with a V belt. Does the AC120v turntable motor needs to be electricaly isolated from the mig welding process? Thanks for the advice.



[Log in to Reply]  [No Email]
Bernie in MA

05-27-2004 17:27:15




Report to Moderator
 Re: Re: Weld positioner speed in reply to Slowpoke, 05-27-2004 15:13:57  
I have made a couple hand operated positioners. One is a truck front spindle with the wheel in the vertical (travel) position. The wheel has a piece of highway signpost perforated tubing welded to it for jigs to be pinned to. I reversed the brake action with levers so that the brake is on until you step on the pedal to release it. Contact is made thru a loop of battery cable bolted to the brake backing plate rubbing on the back of the wheel.

The other one is a 36" dia steel plate horizontal with a bolt welded to the underside in the center. There is a 10" dia x 2" high ring around it. This acts as a contact point as well as a bearing on the table that the whole thing sits on. You spin it around by hand to weld what your helper has assembled on the other side. There is a plywood screen in the the middle to shield his/her eyes. I've made $100 an hour assembling small parts with this rig (unfortunately for only 9 hrs that one time).

[Log in to Reply]  [No Email]
Slowpoke

05-27-2004 23:43:17




Report to Moderator
 Re: Re: Re: Weld positioner speed in reply to Bernie in MA, 05-27-2004 17:27:15  
You have great ideas for your positioners, but I don't have a helper to turn while I weld. My original idea was to make a gas tank cleaner/paint mixer. I started with a shaded pole 1/10 hp motor that has a gear reduction to 12 rpm. It was found in a thrift store for $5. I put it on a plate and ran a V belt to a shaft which has a worn out 12" concrete saw blade mounted to the shaft end. The blade has 5/16" holes about every inch around the edge for cooling. I thought they would be good to mount some Kindorf tubing to hold gas tanks. Then I figured I could us it for welding if the speed could be controled over a range rather than fixed speeds using pulleys. The motor and shaft plate is set on a bar supported by two bearings so the device can be rotated 180�. It all sits on two legs about 30" high. I found that the welding clamp fits nicely on the shaft which will turn about 3 RPM for my welding project. I still need to buy an electronic speed control.
My concern now is will welding cause problems with the AC motor or control.

[Log in to Reply]  [No Email]
Bernie in MA

05-28-2004 18:43:58




Report to Moderator
 Re: Re: Re: Re: Weld positioner speed in reply to Slowpoke, 05-27-2004 23:43:17  
My main point was the using the piece of old bare battery cable for a ground. I have a powered positioner that belongs to a company I built air separaters and air line drain tanks for. That job has dried up but they haven't asked for their positioner back yet. I use it once in a while. It has a horizontal turntable as well as rolls and I rigged a u-joint and shaft on an angle to slide the tanks onto so the groove I was welding would have the opening at the top.

The speed control is by a pair of variable-speed pulleys and a gearbox. The motor is a 3-phase 220 and has never given any problems concerning welding. I didn't know there could be any. I did burn up a small universal joint on a shaft because my ground was going thru the joint.

12RPMs is a little fast unless your bead is real small or the tank you're welding is. It's been a while but I think my rpm on a 4" dia tank was 3 or 4, but I was filling a 1/4" deep and wide groove.

[Log in to Reply]  [No Email]
Slowpoke

05-29-2004 00:41:59




Report to Moderator
 Re: Re: Re: Re: Re: Weld positioner speed in reply to Bernie in MA, 05-28-2004 18:43:58  
Using your idea of a battery cable to wipe the turntable gave me the idea to just put the ground clamp on the table drive shaft. 3RPM on a 4" pipe is what I am planing for. To get the speed that slow, an 8" variable pulley is needed at a cost of over $115. I can buy a speed control for about $35. I would guess the powered positioner you have costs at least $1500. They probably forgot you have it. Some day they'll remember....

[Log in to Reply]  [No Email]
Bernie in MA

05-30-2004 17:02:33




Report to Moderator
 Re: Re: Re: Re: Re: Re: Weld positioner speed in reply to Slowpoke, 05-29-2004 00:41:59  
I'm sure they'll ask for it sometime. I bought a Van Norman miller from them. The book with it was printed in 1942. I would say the positioner dates at least that far back. This company got an award for their production during WWII. I can't remember what they were manufacturing, gun parts I think.



[Log in to Reply]  [No Email]
Slowpoke

05-30-2004 23:50:17




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: Weld positioner speed in reply to Bernie in MA, 05-30-2004 17:02:33  
What luck to get a book with a machine that age.
I found a discarded Cincinatti horizontal mill in a scrap bin. The model number plate is blank except for a large "L". It's probably from the same era as yours but I can't find any book for it.
By the way, I found that several of those large welding magnets (Harbor Freight,$1.99 on sale) work good on the positioner when there's no other way to hold the work.

[Log in to Reply]  [No Email]
T_Bone

05-27-2004 03:48:20




Report to Moderator
 Re: Weld positioner speed in reply to Slowpoke, 05-26-2004 01:24:47  
Hi slowpoke,

Your about right, 40ipm or there abouts.

Electrode mfg, wire size, cover gas and equipment all make a huge difference for estimating work done. If I was estimating for a small to mid size job that I personally wasn't going to weld, I'd always make a trip to have a talk with the actual welders to get a real world guessament of there capibilitys using there methods.

If large jobs, then I would spec welding procedure and/or training if needed. Sometimes it paid to buy new equipment at this time if we won the bid as it was cost effective.

Hobart produced a real handy field welding guide many years ago that would probably help you "if" they still publish it. Name was;
Hobart Pocket Welding Manual

Even had estimating guides for consumables. I had a copy for years but lost it as well as several of my good books on my last job before I retired. I never replaced them so now I have to look thru several refference books even to get a answer to simple problems. :(

Have you looked on Lincoln website?

T_Bone

[Log in to Reply]  [No Email]
Farmer/Paul

05-27-2004 02:19:52




Report to Moderator
 Re: Weld positioner speed in reply to Slowpoke, 05-26-2004 01:24:47  
Try the Hobart welding site 'welding talk" lots of knowledgeable people there.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy