Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tool Talk Discussion Forum

Wiring up a motor.

Welcome Guest, Log in or Register
Author 
Mike S

05-03-2004 11:48:48




Report to Moderator

I picked up a 3/4hp motor to use to run a small compressor for airing up the NAA tires and such. Got it at a salvage store and the label is missing. I was able to find out that it came from McMaster Carr and originally is an AO Smith motor. Neither of them will respond to my question. It is an AO Smith BK1072. 3/4hp 3450 rpm, 110/220 volts AC, 56 frame, has a capacitor. There are six contacts on the terminal board. I am trying to find the right wiring diagram for it. Anybody got a clue? I know some of y'all deal with electric motors a lot.
Thanks

[Log in to Reply]   [No Email]
buickanddeere

05-04-2004 21:05:04




Report to Moderator
 Re: Wiring up a motor. in reply to Mike S, 05-03-2004 11:48:48  
Two pairs of winding ends will measure low resistance of approx 2-10 ohms. The two leads to the start windings will measure a "high" resistance of 5-20ohms. On 120v put the three windings in parallel. With 240v put the two run windings in series. Usually the start windings connect at the center point of the two main windings and at either of the line terminals.



[Log in to Reply]  [No Email]
Chip

05-04-2004 16:18:35




Report to Moderator
 Re: Wiring up a motor. in reply to Mike S, 05-03-2004 11:48:48  
The A O Smith catalog shows it should be dia #22 for a BK 1072.A,B,L1,L2 terminals.Red,black red tracer, black tracer wires.110V=line in to L1 & L2,black tracer & red to A,black & red tracer to L1.220V=line in to L1 & L2,black tracer to b,red & black to A, red tracer to L1.CCW rot from back (no shaft).CW swap red &red tracer.



[Log in to Reply]  [No Email]
larry in tn

05-04-2004 05:55:24




Report to Moderator
 Re: Wiring up a motor. in reply to Mike S, 05-03-2004 11:48:48  
Mike
This is what I found in a motor handbook.
120vac
ccw---L1,1,3,8 joined -----L2,2,4,5 joined
cw----L1,1,3,5 " "----- L2,2,4,8 " "

220vac
ccw----L1,1 ----- ----- L2,4,5----- -2,3,8 cw-----L1,1----- ----- ---L2,4,8----- -2,3,5,
Larry



[Log in to Reply]  [No Email]
Mike S

05-04-2004 10:19:32




Report to Moderator
 Re: Re: Wiring up a motor. in reply to larry in tn, 05-04-2004 05:55:24  
Thanks, where you have the number 8, did you mean 6? As there are only 6 places for a wire to go? I'll give it a try this evening and see how it goes.
Mike



[Log in to Reply]  [No Email]
larry in tn

05-04-2004 18:30:26




Report to Moderator
 Re: Re: Re: Wiring up a motor. in reply to Mike S, 05-04-2004 10:19:32  
Mike
You are most likely right. I put down what the book showed. They have 5 and 8 as the starter winding. I checked a couple of my motors and found 5 and 6 as the starter windings.
Larry



[Log in to Reply]  [No Email]
Mike S

05-06-2004 13:29:35




Report to Moderator
 Re: Re: Re: Re: Wiring up a motor. in reply to larry in tn, 05-04-2004 18:30:26  
Would you send me your email address? I would like to email you a picture of the terminal board because it does not look like what you describe. Maybe I cross referenced the wrong motor.
Thanks



[Log in to Reply]  [No Email]
larry in tn

05-07-2004 05:19:15




Report to Moderator
 Re: Re: Re: Re: Re: Wiring up a motor. in reply to Mike S, 05-06-2004 13:29:35  
Mike
[email protected]
Larry



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy