Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Discussion Forum

Torque wrench

Welcome Guest, Log in or Register
Author 
Ludwig

05-13-2002 11:21:24




Report to Moderator

I'm pretty new to the actual "rebuilding" part of engine work, and now I'm up to my neck.
So it looks like I'm going to need a torque wrench. I'm thinking Craftsman, since I have a bunch of their stuff already and I work across the street from a Sears.
Now the question becomes which one?
I'm pretty much set with 3/8" drive because most of my sockets are 3/8", then do I want beam or ratchet?
The beam ones run about 1/2 the price of the others, but all are supposedly accuate within 4%.
Or do I go for the much more expensive digital read out?
Any suggestions are appreciated.

[Log in to Reply]   [No Email]
Skytown Mark

05-20-2002 00:09:24




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
I am in the same spot as you Ludwig. I'm just getting back into mechanic mode. Got some knowlege but lots to learn. I haven't had a real need for a tourque wrench yet (Though I guess I could have used one when I put the oil pan back on my Farmall Super A), I can see that I'm gravitating toward a total engine rebuild project so the day is coming. After reading all the posts here I'm thinking maybe I'll just spend the money on a new seat and think on the wrench a little longer!

[Log in to Reply]  [No Email]
John in Maryland

05-14-2002 14:54:28




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
I saw further down you said something about getting a 1/2" drive socket set. Unless you're dead set on getting a set of chromed ones, you can get impact sockets for a little cheaper usually, and most sets will range from like 1/2" up to 1 1/4". They will be stronger than the chrome ones as well. The only downside is that the sizes are harder to read on them, but if you have them in a rack it only takes a short while to know where each one is. Also, keep them lightly oiled w/like WD40 or something, because they will get a little rust on them if not(though usually wipes right off).

[Log in to Reply]  [No Email]
BFO

05-15-2002 03:38:58




Report to Moderator
 Re: Re: Torque wrench in reply to John in Maryland, 05-14-2002 14:54:28  
The only problem with impact sockets are the wall thickness. You'd be better off spending a little extra and getting the best 12 point set you can afford. Proto's Torque Plus , or Snap-On's Flank Drive are worth looking at. I haven't used a 6 point socket for anything but breaking a tough fastener loose, or on the impact since I bought my Proto 12 points.



[Log in to Reply]  [No Email]
John

05-15-2002 09:16:09




Report to Moderator
 Re: Re: Re: Torque wrench in reply to BFO, 05-15-2002 03:38:58  
Yup, you're right. I've got both kinds and now that you mention it there have been more than a few times they wouldn't fit in something and had to use a different one. Good point!



[Log in to Reply]  [No Email]
Hal/WA

05-14-2002 14:45:44




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
I get the impression you are fairly new at buying tools. If you like working with your hands on the old tractors, trucks, cars, motorcycles or etc, it will amaze you how many tools you accumulate over the years. I started out with a small mechanic tool kit from Sears and still have many of those original 35 year old tools. Along the way I also have collected a couple of thousand dollars more worth of tools, including a 3/8" drive inch-pound wrench and a 1/2" foo-pound wrench. To do a lot of things accurately, you really need both. I keep them in a drawer of my tool chest where they will not get banged around and they are probably about as accurate as when I bought them.

I have had very good luck with the Craftsman tools and really appreciate Sears policy of cheerful replacement of the few tools I have broken or worn out. If you plan to get more tools, and you WILL, if you continue in this hobby, I would suggest buying the largest Craftsman tool set you can afford. The tools in the large sets cost much less than if you buy them piece by piece. It also will save a lot of aggravation when you need a particular tool that you don't have to finish a job.

I wish I had bit the bullet and bought the largest set Sears offered when I was getting started. I would have spent a lot less money and would not have had to improvise so many times. Good luck and have fun.

[Log in to Reply]  [No Email]
Ludwig - thanks everybody

05-14-2002 07:26:52




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
As we say up here "things are just as clear as mud"
Fortunately for me the ski-doo engine is all in foot pounds which makes it pretty simple for me. It really only needs the torque wrench for the head bolts anyhow.
The tractors are nice because most everything is out where you can get at it pretty handy with a wrench too, and since the ski-doo engines are usually on the bench when I'm working on them I'm leaning toward the beam type wrench.
One very handy thing I mentioned before is working across the street from Sears, you can bet I'll be over there today yackking it up with the fellows. Fortunately this one has some fairly knowledgeable tool sellers. One guy was a mechanic for years. He got bored when he retired and now sells tools for 4 hours a day. Real nice guy and has done right by me before. Pretty rare to find that today....

[Log in to Reply]  [No Email]
revredneck

05-14-2002 05:34:36




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
Ludwig,
I own a Snap-On click type for over twenty years, and it's a great torque wrench. If you are intending to do a lot of engine work, then go ahead and buy as good a torque wrench as you can possibly afford. If not, then why not rent one? If you only build one engine a year or so, it's a lot cheaper to use someone else's. It would take a lot of 20 dollar rentals to buy a 3 or 4 hundred dollar torque wrench, and you can rent a high quality one for the same money as buying a cheap one that will not be accurate or may break on you. My 2 cents worth.
Good Luck and God Bless,
Tommy

[Log in to Reply]  [No Email]
Butch

05-14-2002 04:20:04




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
I would go with a beam before one of the cheapo clickers. All of the clickers have a bad habit of geting out of calibration easily and unless a person has a skilled elbow he won't know it. The beam wrenches are a little unhandy to use as you must be looking straight down on the scale but they are pretty bullet proof. Back when money was not as tough I bought a snap-on dial type torqueometer with the indicator light, the high accuracy model 1/2%. Has served me well for 25 years and passes the tester everytime.

[Log in to Reply]  [No Email]
Rod MI

05-13-2002 23:04:56




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
Craftsman dues not warranty the plastic handles on the ratchet type torque wrenches they sale just to let you now I prefer the ratchet type they are better for working on transmission oil pans and stuff where you cant see the scale and have to tack many torque readings if you ever did this you now what I mean Rod MI



[Log in to Reply]  [No Email]
george md

05-13-2002 22:14:30




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
an accurately calibrated click type is a rare
thing and one that remains accurate is even more rare. Most do not like a beam wrench , but they are the most accurate followed by dial reading
type and the worst is click type. I have all 3
types in my shop and use the beam the most , it
is never out of calibration.i don't have , but do have access to a calibrator, and it always puts an end to the arguement of which type is better. If accuracy is more important than speed buy
beam, if speed is more important than accuracy,
buy click type.A good beam is less than 25 dollars. we build engines every day and the beam works well.

george

[Log in to Reply]  [No Email]
Ray,IN

05-13-2002 20:04:52




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
I have a clicker type 1/2" drive torque wrench. My neighbor annually checks it against his Snap-on clicker wrench for accuracy and my Buffalo brand is consistantly the same as his Snap-on. However the Buffalo was about $20, and his Snap-on $$$$. He is a professional and I just use mine for a few hours a month, so the longivity of the Buffalo brand suits my purpose.



[Log in to Reply]  [No Email]
Greaseman

05-13-2002 16:22:52




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
I have a "Thorenson" which I purchased from Advance auto parts, life time guarentee. I have used both the click type as well as the beam type both have advantages and disadvantages. I would be VERY carefull about purchasing any tools from Sears anymore as they have quite a few tools that sort of slip thruough the cracks on the life time guarentee's.



[Log in to Reply]  [No Email]
T_Bone

05-13-2002 16:16:02




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
Hi Ludwig,

I would get a 1/2" beam with a 3/8" reducer. Why?

With a beam you can see if the scale is off and adjust accordingly but not to many guys have a way to caliberate a clicker or digtal accuraetly.

If you get into gear work then an inch pound comes in handy for preloads.

T_Bone



[Log in to Reply]  [No Email]
buck

05-13-2002 15:01:44




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  

On the Craftsman click type torque wrench you may want to ask the people at the tool department if they happen to have or get in the reconditioned torque wrench. Some of the Sears stores carry these at times. About half price.BTW I use the cman click type in 3/8 and 1/2 passed the old beam type on to others.



[Log in to Reply]  [No Email]
MarkB

05-13-2002 14:39:49




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
Something that I was surprised to find is that not all "clicker" torque wrenches work both clockwise and counterclockwise. I found this out when trying to torque the (LH thread) ring gear bolts on my pickup differential with a Craftsman 1/2" drive torque wrench.

For engine work, you'll need a 1/2" drive torque wrench. Might as well get a 1/2" drive socket wrench set while you're at it.



[Log in to Reply]  [No Email]
Ludwig

05-14-2002 07:18:44




Report to Moderator
 Re: Re: Torque wrench in reply to MarkB, 05-13-2002 14:39:49  
Good idea Mark. I just beat the snot out of a crappy junk 1/2" socket wrench on saturday. The first time I stepped on it to turn a bolt it stripped completely out. Granted I only paid $3 for it... The sockets I bought at the same time are good though, I do have a 1/2" breaker bar that I finished the job with (should have started with it) the only problem with my 1/2" set is that there aren't enough sockets.
I think its time for me to pickup another cman set. My last one was $60, I see they've got one now for $100 that comes with 1/2" tools also.

[Log in to Reply]  [No Email]
BFO

05-13-2002 14:13:50




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
I also prefer the click type. My Craftsman 1/2" drive did not hold up well under constant use. I now have a 3/8" flex head, and a 1/2" drive fixed head, both Snap-On, and I would not recommend anything else. I also agree that the 1/2" drive would be the better choice.



[Log in to Reply]  [No Email]
Mark Kw

05-13-2002 12:43:57




Report to Moderator
 Re: Torque wrench in reply to Ludwig, 05-13-2002 11:21:24  
I prefer the click type ones the best. Most are accurate at mid scale to approx 1% which is decent. I have several differnt ones including a 3/8" C-man. Problem with most 3/8" drive torque wrenches is they are normally topped out at 250 inch pounds. The 1/2" drive ones are usually good to 250 foot pounds which is better suited to most engine work. Personally, I have a ATD or something like that and an older C-man, both in 1/2" drive and click type. I had them tested at a cal lab and both fell within 1% center scale and 2% at the upper and lower ends. Never had the 3/8" one checked but the 1/4" Snap-on was dead on at center scale and under 1% at the ends. I also have a snappy 1" drive, never had it checked but I do like it alot.

Beam type are ok but are hard to get into tight areas and you have to be able to see the scale and pointer clearly when using it. Never used a digital so I can't comment on them. If I had to buy a new one today, I would more than likely go with Snap-On again and the click type. I guess it all depends on what you like and need more than anything.

[Log in to Reply]  [No Email]
Joe M

05-14-2002 22:16:32




Report to Moderator
 Re: Re: Torque wrench in reply to Mark Kw, 05-13-2002 12:43:57  
Don't overlook the simple beam type torque wrench.Back in the early 70's I bought a Craftsman 1/2" drive ,0-150 ft-lb beam type torque wrench.It got a fair amount of abuse from exceeding the max torque on many occasions while functioning as a breaker bar and alot of use on automotive,small engines,whatever.Had to reset the pointer a few times during 25 years but the beam never was bent.The accuracy was always good enough providing the bolts,etc were reasonably clean.I had to torque some valve cover bolts to 7 ft-lbs and hung an appropriate amount of weight on it beforehand to check the accuracy.Darned if it didn't read about 7 on the 0-150 scale.The downside of this type is when you can't see the scale and pointer or you want to quickly tighten a bunch of fasteners to the same torque.The upside is they stay in calibration unless you abuse the snot out of it ,so theres no calibration to worry about or pay for.I passed it on 3 years ago after the rivets holding the scale on started falling off.Went out and for the princely sum of 25 bucks bought another from sears.Note: craftsman torque wrench warranty is only 1 year.Only other thing to add is don't confuse in-lbs and ft-lbs and if a specified torque seems too high or too low,find out the whole story if it's critical.The other types of torque wrenches can be quite nice to use and own if there's a need but the inexpensive beam types can serve the weekend mechanic well.

[Log in to Reply]  [No Email]
Ludwig

05-13-2002 14:33:53




Report to Moderator
 Re: Re: Torque wrench in reply to Mark Kw, 05-13-2002 12:43:57  
thanks, thats kinda what I needed to know.
The immediate need is for my '70 Ski-Doo engine which is currently all apart. Then there'll be a '76 Ski-Doo, '77 Ski-Doo, '28 Farmall Regular and a '52 Farmall Super M. So I guess I'd do to buy a better quality wrench. It won't be coming from India or China, you can bet that.
At nearly $200 new you can bet it won't come from Snap-on either. Although I figure if it did I'd definately never buy another...
Craftsman is about $60 and Northern Tool has one for $20.
I'm leaning toward the Craftsman for quality. I'll probably pick up a set of 1/2" 6 point sockets at the same time.

[Log in to Reply]  [No Email]
Bob

05-13-2002 16:51:50




Report to Moderator
 Re: Re: Re: Torque wrench in reply to Ludwig, 05-13-2002 14:33:53  
Don't know what specific Ski-Doo engine you're talking about, but I would assume you would be talking INCH POUNDS for those, and I'm not sure how accurate a 1/2" torque wrench would be at the lower foot-pound readings that inch pound readings would convert to.
You may be better off buying a 1/2" torque wrench AND a 3/8" torque wrench. I realize this will take quite a chunk of money, but one single engine, or engine part, ruined by improper torque would probably make up the diffence to have the proper torque wrench for the job!

[Log in to Reply]  [No Email]
Murray Dunn

05-13-2002 19:29:45




Report to Moderator
 Re: Re: Re: Re: Torque wrench in reply to Bob, 05-13-2002 16:51:50  
With any Torque qrench be sure you read in a good rebuilding manual about proper lubricarion for the threads and follow the torque specs for specific engine.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy