Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Discussion Forum

Gen set

Welcome Guest, Log in or Register
Author 
Mark Kw

04-03-2002 07:52:55




Report to Moderator

Looking for input on a small generator set. Have not had time to look around at what's out there in the small stuff yet, more used to dealing with the big diesels and 480 v 3ph.

What I'd like is something light in weight and small in size. Don't need a whole lot of power, can get by with 20 amps of 120vac. Going to use it for running the small hand power tools up to a 9" grinder so I ain't beating the snot out of the welding machine just for electric power. Also, would like something that runs quieter than the twin cyl Onan so I can somewhat maintain my sanity.

I'd like to have one that'll put out about 15 amps of 220vac as well but it's not necessary. Long run time and low fuel consumption is also a plus. Unit will likely run 10 hours at a time when needed so I want something that'll hold up over time.

Any thoughts are very welcome.

[Log in to Reply]   [No Email]
Bill

04-07-2002 13:27:28




Report to Moderator
 Re: gen set in reply to Mark Kw, 04-03-2002 07:52:55  
I currently have a 16 horse Briggs & Stratton Vangaurd driven Generator. I sympathize with the bark of your fully loaded Onan..... My Briggs is just for standby use so I'm not really interested in it's longevity (Sorry Briggs haters, I just don't care. Had it 5 years & have less than 40 hours on it while occasionally the neighbors sit in the dark I take hot showers & watch TV with the well pump pumping & hot air heat running for under $1500) To that end I pulled the factory muffler off & stuck an inch and a half passenger car muffler on her &..... Its QUIET!!!!! even loaded..... In your situation my 2 cents worth/something to consider: Look for a take out generator from a Motorhome/RV. They run 1800rpm, long life rated/have factory installed low noise mufflers & can be picked up reasonable. In my situation, a former Troy Built/Gardenway design person gave me a tip: Convert the thing to propane. It's easier to store & will quadruple or better the engine life expectancy as the propane burns SOOOOO much cleaner. Will get around to that but must admit it's low on my priorities..... Done expounding. Think it over & good luck.... Might want to consider that propane thing for the welder. After asking around the Garden Way guy knew what he was talking about as far as longevity.....

[Log in to Reply]  [No Email]
G Taylor

04-07-2002 14:14:50




Report to Moderator
 Re: Re: gen set in reply to Bill, 04-07-2002 13:27:28  
There was a company selling LP or natural gas carbs & the venturi systems for small engines on E-bay. Get a beefy cable or chain & lock for the generator too.Jealous,desperate people and thieves were "borrowing" any generator not tied down or guarded during the Quebec ice storm.



[Log in to Reply]  [No Email]
Bill

04-07-2002 15:39:46




Report to Moderator
 Re: Re: Re: gen set in reply to G Taylor , 04-07-2002 14:14:50  

THANKS!!!! Will look for the propane conversion on E-Bay.



[Log in to Reply]  [No Email]
Brad

04-07-2002 21:50:57




Report to Moderator
 Re: Re: Re: Re: gen set in reply to Bill, 04-07-2002 15:39:46  
I agree totally about the idea of propane, but the problem I would have is the same reason I have a gas engine welder on my gas engine truck. I want a diesel truck, but then I would have to run 2 different pumps at the gas station until I get my diesel generator. But even if I had a matched set of diesel or gas engines and then a propane one in addition, I'd have to pull up to the propane and get filled up there as well. Call me stupid, but I'm usually wanting to get to the job site and it is a lot easier for me to just have one pump in hand for all my engine operated equipment on my rig..... ..truck, welder, compressor..... . The ideal thing would be to convert my truck over to propane, then converting everything else to propane would be a cinch. I do like the idea of everything being propane.

Brad

[Log in to Reply]  [No Email]
Mike W

04-04-2002 20:32:07




Report to Moderator
 Re: gen set in reply to Mark Kw, 04-03-2002 07:52:55  
Hi Mark, I've read that the typical hardware store generators are good for about 750 hours. I would look for one thats runs at 1800 vs 3600 rpm. Don't know if a small one is made for 1800. Do you have any experience with the small diesels made in China?



[Log in to Reply]  [No Email]
G Taylor

04-06-2002 09:03:15




Report to Moderator
 Re: Re: gen set in reply to Mike W, 04-04-2002 20:32:07  
The Chinese generators are usually clones of Yanmars, so close the parts will often interchange. As for quality of the alloys, heat treat, machining tolerances it's doubtful. At Toronto International they use portable Yanmar single cylinder air cooled diesels to operate service lights during runway maintaince. Some have over 10,000 hrs with only oil/filter changes and checking the injector once or twice. They will sludge up and smoke if lightly loaded in cold weather. My cousin has a 3500 watt Yanmar unit on his highway tractor to provide power/heat or cooling rather than idling the tractor engine. Paid for in less than one year with fuel & service cost reduction. Wouldn't bother to purchase small a portable gas generator after seeing these units.

[Log in to Reply]  [No Email]
Brad

04-03-2002 12:44:12




Report to Moderator
 Re: gen set in reply to Mark Kw, 04-03-2002 07:52:55  
I would tend to look in the Honda generator, OHV, market. If you are looking for something fairly quiet, I think they are about the quietest. From what I have read, the majority of their engines, in generator form, are around the 70 db mark. I don't think that is too loud compared to some of the others I have been around.

Brad



[Log in to Reply]  [No Email]
Mark Kw

04-08-2002 10:47:13




Report to Moderator
 Re: Re: gen set in reply to Brad, 04-03-2002 12:44:12  
I ended up getting my brother's Coleman powerbase 5000 for $450. He got it new and never used it, the couple times it was used, I was the one using it. Light enough not to be a problem moving myself. It will suffice for what I need right now but I am looking at a couple things for the future.

I appreciate the comments on Yanmar diesels. I had a guy post on my tool board about one he is considering selling. I'd like to go with something like this for the new medium duty service truck as a permanent fixture...just as soon as I get some time to put a new truck together.

I also appreciate the comments on coverting to LP. I use LP for my field cutting so it's not like I don't carry a tank with me anyway. I had considered this before but never followed up on it. I have Onan's on the Miller welders and one that will be on the big genset that's going on the heavy duty service truck. Some questions on this topic:

1- should I use genuine Onan LP conversion kits or is there anything better? (Not concerned with price, only quality. I know Onan gets a bit pricy on their products but they have also given me a lot of trouble free service for the money)

2- Is there any problems with using LP in cold temps? (Never had any LP engines that were stored in unheated areas.)

3- How much time and effort is involved in converting to LP? Is it a matter of just removing the carb and installing the regulator or is there a lot more to it?

Many thanks for the input thus far.
Mark Kw

[Log in to Reply]  [No Email]
Fred OH

04-09-2002 11:03:40




Report to Moderator
 Re: Re: Re: gen set in reply to Mark Kw, 04-08-2002 10:47:13  
Mark, I saw some interesting posts here as you did and they pretty well covered most topics but one. I have an old Kohler 20kw generator that will run on gas, propane or natural gas. You change over and reset the timing if I'm not mistaken. Then, I think it is derated somewhat as the lpg and natural gasses don't have as much kick as the gasoline. Just thinkin about the Onan engine... would it have enough umph on the lower combustable fuels? Maybe being that we're kickin this around now, someone with more knowledge will step forward and enlighten us. I like the propane bit, I have had a couple of Clark forklifts with it and one year after an oil change...it looked just like you changed it yesterday. L8R....Fred OH

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy