TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Tractor Pulling Discussion Forum

TimC would like to get flow bench info if possib

Welcome Guest, Log in or Register

Author

Turbine Dude

01-20-2004 17:11:29

Report to Moderator

If your out there I would like to get that flow bench info sent to me. Sounds great I will have to read over it and give it a wirl. Its amazing how much good info is out there that can be cross applied Hmmm. Its just a matter of doing a little extra caricular reading. Thanks in advance.
Turbine Dude. [email protected]

[Log in to Reply] [No Email]

TimC

01-21-2004 09:42:39

Report to Moderator

Re: TimC would like to get flow bench info if po in reply to Turbine Dude, 01-20-2004 17:11:29

Link

is the link to the new board. Bruce should have the old archives added soon. Very good info here.

Also search the web for intake/exhaust port velocity. Don't get hung up on flow numbers. IMHO is is much better to flow the correct cfm at the rpm range you want, i.e. peak torque or max allowed rpm and maintain peak velocity at that rpm range i.e. .6 mach and get quality flow rather than just reach xxx cfm flow. Study anything by Vizard, Mondello. (spelling?)

Other helpful tools are Dynomation and Engine Expert by Curtis Leverton and Alan Lockheed respectivly. A good book is Desktop Dynos which explains wave action simulation.

[Log in to Reply] [No Email]

miss'b'havin

01-23-2004 05:49:16

Report to Moderator

Re: Re: TimC would like to get flow bench info i in reply to TimC, 01-21-2004 09:42:39

TimC-
I too would appreciate your flow bench plans! If you could please email them to me at [email protected]. Thanks a lot in advance!

[Log in to Reply] [No Email]

TimC

01-23-2004 10:42:08

Report to Moderator

Re: Re: Re: TimC would like to get flow bench inf in reply to miss'b'havin, 01-23-2004 05:49:16

I get a delivery failure to your emial address. Email my netzero account then I can verify your emial address and will send them from work on monday unless you send it before 4:30 CST today.

[email protected]

I believe that is right. use it very seldom.

[Log in to Reply] [No Email]

JD Fan

01-21-2004 08:06:12

Report to Moderator

Re: TimC would like to get flow bench info if po in reply to Turbine Dude, 01-20-2004 17:11:29

I would be interested in your flow bench information, to use during the porting process.

[Log in to Reply] [No Email]

Allis

01-21-2004 06:16:39

Report to Moderator

Re: TimC would like to get flow bench info if po in reply to Turbine Dude, 01-20-2004 17:11:29

I would also like a set of plans and info on parts etc. if it is not to much trouble. Thank's

[Log in to Reply] [No Email]

TimC

01-20-2004 18:38:18

Report to Moderator

Re: TimC would like to get flow bench info if po in reply to Turbine Dude, 01-20-2004 17:11:29

Yours appears to have been recieved by your mailbox. Will check for a returned notice Wed AM.

[Log in to Reply] [No Email]

redneck puller

01-20-2004 17:57:55

Report to Moderator

Re: TimC would like to get flow bench info if po in reply to Turbine Dude, 01-20-2004 17:11:29

TimC can i get your flow bench plans also. I would like to get one set up.
Thanks [email protected]

[Log in to Reply] [No Email]

TimC

01-21-2004 06:12:11

Report to Moderator

Re: Re: TimC would like to get flow bench info i in reply to redneck puller , 01-20-2004 17:57:55

I get a message delivery failure to [email protected]

[Log in to Reply] [No Email]

TimC

01-20-2004 18:37:16

Report to Moderator

Re: Re: TimC would like to get flow bench info i in reply to redneck puller , 01-20-2004 17:57:55

I'll have to send them one at a time tomorrow. The complete set in zipped format is to large for your mailbox.

[Log in to Reply] [No Email]

puller

01-20-2004 18:35:14

Report to Moderator

Re: Re: TimC would like to get flow bench info i in reply to redneck puller , 01-20-2004 17:57:55

mee too!!lol...I wanna see how to build one. Thanks alot

[Log in to Reply] [No Email]

TimC

01-20-2004 18:42:35

Report to Moderator

Re: Re: Re: TimC would like to get flow bench inf in reply to puller, 01-20-2004 18:35:14

Anybody else can wait until tomorrow. Yours has been sent as long as you can recieve 4 meg files.

If you guys want some tips on locating parts and the discussion board that explains everything you ever wanted to know about how benches work feel free to reply to the original.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy